AP601-PCB2140 TriQuint, AP601-PCB2140 Datasheet
AP601-PCB2140
Specifications of AP601-PCB2140
Available stocks
Related parts for AP601-PCB2140
AP601-PCB2140 Summary of contents
Page 1
... Ordering Information 192 ºC Part No. Input P6dB 0.1 mA AP601 0.1 mA AP601-PCB900 80 mA AP601-PCB1960 1930-1990 MHz Evaluation board 2.3 W AP601-PCB2140 2110-2170 MHz Evaluation board Functional Diagram SMT The device ACLR1 vs. Output Power vs. Icq WCDMA, Vcc = 28V, 2140 MHz, 25 ˚ -45 ...
Page 2
... AP601 High Dynamic Range 1.8W 28V HBT Amplifier S-Parameters ( Gain / Maximum Stable Gain 40 DB(|S(2,1)|) -10 0 0.5 1 1.5 Frequency (GHz) The gain for the unmatched device in 50 ohm system is shown as the trace in black color. For a tuned circuit for a particular frequency expected that actual gain will be higher the maximum stable gain. The maximum stable gain is shown in the marked red line. ...
Page 3
... Vpd is used as a reference for the internal active bias circuitry. It can be used to turn on/off the amplifier. Ipd depends on the Icq quiescent current setting. Ipd can 2mA at a quiescent current setting of 40mA. 3. Vbias should be maintained fixed at +5V. Ibias will change based on RF input power level. It can 2mA on the AP601 ...
Page 4
... The center of C24 is placed at 0.285” (11.7°@ 940 MHz) from the edge of the AP601 (U1). 5. The center of C26 is placed at 0.055” (2.3° @ 940 MHz) from the edge of the AP601 (U1). 6. The center 0.095” (3.9° @ 940 MHz) from the center of C26. ...
Page 5
... The center placed at 0.085” (7.3° @ 1960 MHz) from the edge of the AP601 (U1). 5. The center of C19 is placed at 0.755” (64.5° @ 1960 MHz) from the edge of the AP601 (U1). 6. The center of C18 is placed at 0.300” (25.6° @ 1960 MHz) from the center of C19. ...
Page 6
... AP601 High Dynamic Range 1.8W 28V HBT Amplifier 2110-2170 MHz Application Circuit (AP601-PCB2140) Typical WCDMA Performance at 25 ° channel power of +24 dBm Frequency 2140 MHz W-CDMA Channel Power +24 dBm Power Gain 13.5 dB Input Return Loss 12 dB Output Return Loss 8 dB ACLR ...
Page 7
... AP601 High Dynamic Range 1.8W 28V HBT Amplifier 2110-2170 MHz Application Circuit Performance Plots W-CDMA 3GPP Test Model 1+64 DPCH, 60% clipping, PAR = 8 0.01% Probability, 3.84 MHz BW Gain vs. Output Power vs. Temperature CW tone, Vcc = 28V, Icq = 40 mA, 2140 MHz -40 ˚ ˚C 85 ˚ Output Power (dBm) ACLR1 vs ...
Page 8
... High Dynamic Range 1.8W 28V HBT Amplifier 2110-2170 MHz Application Note: Changing Icq Biasing Configurations The AP601 can be configured to operate with lower bias current by varying the bias-adjust resistor – R2. The recommended circuit configurations shown previously in this datasheet have the device operating with the quiescent current (I This biasing level represents the best tradeoff in terms of linearity and efficiency ...
Page 9
... The center placed at 0.050” (5.1° @ 2.35 GHz) from the edge of the AP601 (U1). 4. The center of C19 is placed at 0.650” (66.6° @ 2.35 GHz) from the edge of the AP601 (U1). 5. The center of C30 is placed at 0.110” (11.3° @ 2.35 GHz) from the center of C19. ...
Page 10
... Junction Temperature (°C) Product Marking The component will be laser marked with a “AP601-F” product label with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part will be located on the website in the “Application Notes” section. ...