AVR-IO-M16 Olimex Ltd., AVR-IO-M16 Datasheet

MCU, MPU & DSP Development Tools DEV BRD FOR ATMEGA16 16MHZ 5V

AVR-IO-M16

Manufacturer Part Number
AVR-IO-M16
Description
MCU, MPU & DSP Development Tools DEV BRD FOR ATMEGA16 16MHZ 5V
Manufacturer
Olimex Ltd.
Datasheet

Specifications of AVR-IO-M16

Processor To Be Evaluated
ATMega16-16AI
Data Bus Width
8 bit
Interface Type
RS-232, JTAG
Dimensions
80 mm x 100 mm
Operating Supply Voltage
5 V
Silicon Manufacturer
Atmel
Core Architecture
AVR
Silicon Core Number
ATmega16
Kit Contents
Board
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
1701520 25R4411
AVR-IO-M16 development board
Users Manual
Rev.A, July 2008
Copyright(c) 2008, OLIMEX Ltd, All rights reserved

Related parts for AVR-IO-M16

AVR-IO-M16 Summary of contents

Page 1

... AVR-IO-M16 development board Copyright(c) 2008, OLIMEX Ltd, All rights reserved Users Manual Rev.A, July 2008 ...

Page 2

... FR-4, 1.5 mm (0.062"), green soldermask, white silkscreen component print - Dimensions 80x100 mm (3.9 x 3.15") ELECTROSTATIC WARNING: The AVR-IO-M16 board must not be subject to high electrostatic potentials. General practice for working with static sensitive devices should be applied when working with this board. BOARD USE REQUIREMENTS: Cables: ...

Page 3

... PROCESSOR FEATURES: AVR-IO-M16 uses ATMega16 MCU from Atmel with the following features: High-performance, Low-power AVR® 8-bit Microcontroller – Advanced RISC Architecture – 131 Powerful Instructions – Most Single-clock Cycle Execution – General Purpose Working Registers – Fully Static Operation – ...

Page 4

BLOCK DIAGRAM: ...

Page 5

MEMORY MAP: ...

Page 6

BOARD LAYOUT: ...

Page 7

...

Page 8

SCHEMATIC: ...

Page 9

... POWER SUPPLY CIRCUIT: The power supply of AVR-IO-M16 is taken from Power jack connector. The center pin is positive. The voltage range is +12-14VDC. The consumption with no relays switched on RESET CIRCUIT: AVR-IO-M16 reset circuit is made with ZM33064 with typical threshold 4.5V. When the voltage falls bellow that minimum, the MSU resets. ...

Page 10

... NC 9 PC5(TDI) 10 GND This connector allows programming and debugging via AVR-JTAG or other compatible tools. TDI Input Test Data In. This is the serial data input for the shift register. TDO OutputTest Data Out. This is the serial data output for the shift register. Data is shifted out of the device on the negative edge of the TCK signal ...

Page 11

... GND This connector allows programming via AVR-PG1, AVR-PG2 or other compatible tool. MOSI Master Out Slave In. SPI data transfer signal either input or output I/O depending on whether the MCU is master or slave. MISO Master In Slave Out. SPI data transfer signal either input or output I/O depending on whether the MCU is master or slave ...

Page 12

MECHANICAL DIMENSIONS: ...

Page 13

... AVAILABLE DEMO SOFTWARE: Check for available demo software for AVR-IO-M16 on our website: www.olimex.com/dev. ...

Page 14

... ORDER CODE: AVR-IO-M16 How to order? You can order to us directly or by any of our distributors. Check our web All boards produced by Olimex are ROHS compliant Revision history: REV.A - created July 2008 – assembled and tested (no kit, no soldering required) www.olimex.com/dev for more info. ...

Page 15

... OLIMEX in good faith. However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this ...

Related keywords