LPC-P2919 Olimex Ltd., LPC-P2919 Datasheet

MCU, MPU & DSP Development Tools DEV BRD FOR LPC2919 768KB FLASH 56KBSRAM


Manufacturer Part Number
MCU, MPU & DSP Development Tools DEV BRD FOR LPC2919 768KB FLASH 56KBSRAM
Olimex Ltd.

Specifications of LPC-P2919

Processor To Be Evaluated
LPC2919 ARM968E-S
Data Bus Width
16 bit, 32 bit
Interface Type
RS-232, CAN, SPI
140 mm x 89 mm
Operating Supply Voltage
9 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
LPC-P2919 development board
Users Manual
All boards produced by Olimex are ROHS compliant
Rev.A, October 2009
Copyright(c) 2011, OLIMEX Ltd, All rights reserved
Page 1

Related parts for LPC-P2919

LPC-P2919 Summary of contents

Page 1

... LPC-P2919 development board All boards produced by Olimex are ROHS compliant Copyright(c) 2011, OLIMEX Ltd, All rights reserved Users Manual Rev.A, October 2009 Page 1 ...

Page 2

... LPC-P2919 board is easy to use development board with LPC2919 - ARM9 microcontroller with CAN and LIN produced by NXP Semiconductors. With LPC-P2919 you can explore the features of LPC29XX family on budged, the board has everything necessary to build simple applications: reset and oscillator circuits, JTAG port for programming and debugging, CAN, LIN, RS232, SD/MMC, LCD, three status LEDs and two user buttons ...

Page 3

... ELECTROSTATIC WARNING: The LPC-P2919 board is shipped in protective anti-static packaging. The board must not be subject to high electrostatic potentials. General practice for working with static sensitive devices should be applied when working with this board. BOARD USE REQUIREMENTS: Cables: The cable you will need depends on the programmer/debugger you use. If you use ARM-USB-OCD, you will need RS232 cable and 1 ...

Page 4

Two 8-channel 10-bit ADCs provide a total 16 analog inputs, with conversion – times as low as 2.44 μs per channel. Each channel provides a compare function to minimize interrupts. 24 level-sensitive external interrupt pins, including CAN and LIN wake- ...

Page 5

Block Diagram: Page 5 ...

Page 6

... MEMORY MAP: For more details see LPC2919FBD144 datasheet. Page 6 ...

Page 7

SCHEMATIC 1 N475 1 C30) 1N4 75 1(B ZX 85C3 CAN0_L CAN1_L 1 0k DATA + Page 7 + 100nF 100nF 47uF/6.3V 47uF/6. 10uF/6.3V + 47uF/6.3V + 100nF 100nF + ...

Page 8


Page 9

... LPC-P2919 can take power from two sorces: External power supply 9.0-12 6.0V AC. – +5V_JLINK from JTAG connector – RESET CIRCUIT LPC-P2919 reset circuit includes pin 15 of JTAG connector, pin and RESET button. CLOCK CIRCUIT Quartz crystal 16 MHz is connected to LPC-P2919 pin 75 (XOUT_OSC) and pin 76 (XIN_OSC). JUMPER DESCRIPTION PWR_SEL When 1-2 are shorted – ...

Page 10

... Power-on LED (red) with name PWR – this led shows that +3.3V is applied to the board. User button with name BUT1 connected to LPC2919 pin 27 (P2.26/TIMER0_CAP2/TIMER0_MAT2/EXTINT6). User button with name BUT2 connected to LPC2919 pin 28 (P2.27/TIMER0_CAP3/TIMER0_MAT3/EXTINT7). Reset button with name RESET connected to LPC2919 pin 73 (RSTN). Trimpot with name AN_TRIM connected to LPC2919 pin 142 (P0.23/ADC2_IN7/PWM2_MAT5/EXTBUS_A19). LCD 8X1 Page 10 ...

Page 11

... The JTAG connector allows the software debugger to talk via a JTAG (Joint Test Action Group) port directly to the core. Instructions may be inserted and executed by the core thus allowing LPC2919 memory to be programmed with code and executed step by step by the host software. For more details refer to IEEE Standard 1149.1 - 1990 Standard Test Access Port and Boundary Scan Architecture and LPC2919 datasheets and users manual ...

Page 12

RS232: Pin # UEXT: Pin # PWR_JACK: Pin # 1 2 Signal Name NC T2OUT R2IN NC GND ...

Page 13

CAN0: Pin# Signal 1 GND 2 CAN0_L 3 CAN0_H CAN1: Pin# Signal 1 GND 2 CAN1_L 3 CAN1_H LIN0: Pin# Signal 1 LIN0_PWR LIN Power 2 LIN0_BUS LIN 3 GND LIN1: Pin# Signal 1 LIN1_PWR LIN Power 2 LIN1_BUS LIN ...

Page 14

SD/MMC Pin # Signal Name Pin # SPI0_SCS0 9 SPI0_MOSI 10 GND 11 3.3V 12 SPI0_SCK 13 GND 14 SPI0_MISO 15 MCIDAT1 Page 14 Signal Name MCIDAT2 WP1 NC NC CP1 WP2 ...

Page 15

EXT Pin # Signal Name 1 +5V 3 P0.0 5 P0.2 7 P0.4 9 P0.6 11 P0.10 13 P0.12 15 P0.14 17 P0.16 19 P0.18 21 P0.20 23 P0.22 25 P0.30 27 P1.1 29 P1.3 31 P1.5 33 P1.7 35 ...

Page 16

... C-bus controllers support multiple address recognition and a bus monitor – mode. SPI The LPC2919 contains three Serial Peripheral Interface modules (SPIs) to allow synchronous serial communication with slave or master peripherals. The key features are: Master or slave operation. – Each SPI supports up to four slaves in sequential multi-slave operation. ...

Page 17

Serial clock-rate master mode: fserial_clk ≤ f – Serial clock-rate slave mode: fserial_clk = f – Internal loopback test mode. – The SPI module can operate in: Master mode: – Normal transmission mode. – Sequential slave mode. – Slave mode. ...

Page 18

MECHANICAL DIMENSIONS All measures are in inches. Page 18 ...

Page 19

AVAILABLE DEMO SOFTWARE Buttons and LCD demo – Port_LCD_UART demo – SD slot demo – Page 19 ...

Page 20

... ORDER CODE LPC-P2919 How to order? You can order to us directly or by any of our distributors. Check our web Board revision history: Rev. A Manual revision history: Rev. A instead of LPC2919FBD144 features, were given for LPC2919FBD144/01 – assembled and tested (no kit, no soldering required) www.olimex.com/dev for more info. ...

Page 21

... This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product ...

Related keywords