AFBR-5715PZ Avago Technologies US Inc., AFBR-5715PZ Datasheet - Page 3
![Fiber Optic Transmitters, Receivers, Transceivers Transceiver](/photos/15/67/156703/afbr-57r5p-afct-57r5tp_wht_sml.jpg)
AFBR-5715PZ
Manufacturer Part Number
AFBR-5715PZ
Description
Fiber Optic Transmitters, Receivers, Transceivers Transceiver
Manufacturer
Avago Technologies US Inc.
Type
TX/RXr
Series
-r
Specifications of AFBR-5715PZ
Function
Designed for those applications requiring DMI features.
Product
Transceiver
Data Rate
1.25 GBd
Wavelength
850 nm
Maximum Rise Time
0.26 ns/0.22 ns (Typ)
Maximum Fall Time
0.26 ns/0.22 ns (Typ)
Pulse Width Distortion
0.227 ns (Max)/0.266 ns (Max)
Operating Supply Voltage
3.135 V to 3.465 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 10 C
Package / Case
SFP
Mounting Type
SFP
Voltage - Supply
3.135 V ~ 3.465 V
Connector Type
LC Duplex
Applications
Ethernet
Optical Fiber Type
TX/RX
Data Transfer Rate
1250MBd
Optical Rise Time
0.26/0.22ns
Optical Fall Time
0.26/0.22ns
Jitter
0.227/0.266ns
Operating Temperature Classification
Commercial
Peak Wavelength
850nm
Package Type
SFP
Operating Supply Voltage (min)
3.135V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.465V
Operating Temp Range
-10C to 85C
Mounting
Snap Fit To Panel
Pin Count
20
Package
20SFP
Rise Time
0.26/0.22(Typ) ns
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
Multimode Glass
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AFBR-5715PZ
Manufacturer:
Avago Technologies
Quantity:
135
Installation
The AFBR-571 Z can be installed in or removed from any
MSA-compliant Pluggable Small Form Factor port
regardless of whether the host equipment is operating or
not. The module is simply inserted, electrical-interface first,
under finger-pressure. Controlled hot-plugging is ensured
by 3-stage pin sequencing at the electrical interface. This
printed circuit board card-edge connector is depicted in
Figure 2.
As the module is inserted, first contact is made by the
housing ground shield, discharging any potentially
component-damaging static electricity. Ground pins
engage next and are followed by Tx and Rx power supplies.
Finally, signal lines are connected. Pin functions and
sequencing are listed in Table 2.
Transmitter Section
The transmitter section includes the Transmitter Optical
Subassembly (TOSA) and laser driver circuitry. The TOSA,
containing an 850 nm VCSEL (Vertical Cavity Surface
Emitting Laser) light source, is located at the optical
interface and mates with the LC optical connector. The
TOSA is driven by a custom IC, which converts differential
logic signals into an analog laser diode drive current. This
Tx driver circuit regulates the optical power at a constant
level provided the data pattern is DC balanced (8B10B
code for example).
Transmit Disable (Tx_Disable)
The AFBR-571 Z accepts a TTL and CMOS compatible
transmit disable control signal input (pin 3) which shuts
down the transmitter optical output. A high signal
implements this function while a low signal allows normal
transceiver operation. In the event of a fault (e.g. eye safety
circuit activated), cycling this control signal resets the
module as depicted in Figure 6. An internal pull-up resistor
disables the transceiver transmitter until the host pulls
the input low. Host systems should allow a 10ms interval
between successive assertions of this control signal.
Tx_Disable can also be asserted via the 2-wire serial
interface (address A2h, byte 110, bit 6) and monitored
(address A2h, byte 110, bit 7).
The contents of A2h, byte 110, bit 6 are logic OR’d with
hardware Tx_Disable (pin 3) to control transmitter
operation.
3
Transmit Fault (Tx_Fault)
A catastrophic laser fault will activate the transmitter signal,
TX_FAULT, and disable the laser. This signal is an open
collector output (pull-up required on the host board). A
low signal indicates normal laser operation and a high
signal indicates a fault. The TX_FAULT will be latched high
when a laser fault occurs and is cleared by toggling the
TX_DISABLE input or power cycling the transceiver. The
transmitter fault condition can also be monitored via the
2-wire serial interface (address A2, byte 110, bit 2).
Eye Safety Circuit
The AFBR-571 Z provides Class 1 eye safety by design
and has been tested for compliance with the requirements
listed in Table 1. The eye safety circuit continuously
monitors optical output power levels and will disable the
transmitter and assert a TX_FAULT signal upon detecting
an unsafe condition. Such unsafe conditions can be created
by inputs from the host board (Vcc fluxuation, unbalanced
code) or faults within the module.
Receiver Section
The receiver section includes the Receiver Optical
Subassembly (ROSA) and amplification/quantization
circuitry. The ROSA, containing a PIN photodiode and
custom trans-impedance preamplifier, is located at the
optical interface and mates with the LC optical connector.
The ROSA is mated to a custom IC that provides post-
amplification and quantization. Also included is a Loss Of
Signal (LOS) detection circuit.
Receiver Loss of Signal (Rx_LOS)
The Loss Of Signal (LOS) output indicates an unusable
optical input power level. The Loss Of Signal thresholds
are set to indicate a definite optical fault has occurred
(e.g., disconnected or broken fiber connection to
receiver, failed transmitter, etc.).
The post-amplification IC includes transition detection
circuitry which monitors the ac level of incoming optical
signals and provides a TTL/CMOS compatible status
signal to the host (pin 8). An adequate optical input
results in a low Rx_LOS output while a high Rx_LOS
output indicates an unusable optical input. The Rx_LOS
thresholds are factory-set so that a high output indicates
a definite optical fault has occurred. For the AFBR-5715Z
family, Rx_LOS can also be monitored via the 2-wire
serial interface (address A2h, byte 110, bit 1).