MC00L1NZQD C&K Components, MC00L1NZQD Datasheet - Page 5
![SWITCH ROTARY SP 12POS EYELET](/photos/15/16/151614/mc00l1nzqd_sml.jpg)
MC00L1NZQD
Manufacturer Part Number
MC00L1NZQD
Description
SWITCH ROTARY SP 12POS EYELET
Manufacturer
C&K Components
Series
Mr
Datasheet
1.638101000.pdf
(5 pages)
Specifications of MC00L1NZQD
Number Of Positions
12
Number Of Decks
1
Number Of Poles Per Deck
1
Circuit Per Deck
SP12T
Contact Rating @ Voltage
0.25A @ 125VAC
Actuator Type
Flatted (3.17mm dia)
Mounting Type
Panel Mount
Termination Style
Solder Lug
Orientation
Vertical
Angle Of Throw
30°
Contact Current Max
6A
Switch Terminals
Solder Lug
Indexing Angle
30°
Total # Of Positions
12
Pole Throw Configuration
SP
Actuator Style
Shaft
Current Rating (max)
0.25A
Illumination Type
Not Required
Ac Voltage Rating (max)
125VVAC
Dc Voltage Rating (max)
28VVDC
Contact Material
Copper Alloy
Contact Plating
Silver
Product Height (mm)
31.37mm
Product Depth (mm)
13.34mm
Product Length (mm)
13.34mm
Operating Temp Range
-30C to 85C
Mounting Style
Panel
Terminal Type
Solder Lug
Index Angle
30 deg
Contact Style
Non Shorting
Contact Form
SP
Voltage Rating
125 Volts
Current Rating
250 mAmps
Contact Rating
250 mAmps at 125 VoltsAC, 28 VoltsDC
Voltage Rating Ac
125 Volts
Voltage Rating Dc
28 Volts
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*MC00L1NZQD
CKC7009
CKC7009
M Series
Half-inch Rotary Switches
SEAL
D
F
NO EPOXY SEAL
SPLASHPROOF SHAFT AND PANEL SEAL
IP67 approved
Setting Stops With Stop Pins
MA00, MB00, MC00 & MD00 Models Only:
The number of switch positions or stops are adjustable by means of stop pins provided with each switch. Switches are normally
shipped with stop pins and hardware in bulk, not installed. Without stop pins, switches have full 360º rotation and no stops.
Note that all two pole models begin to repeat when actuated 180º or more.
To set stops, refer to figures 1 & 2. Orient switch so that terminal no. 1 is as shown. Turn actuator to position 1, using flats on
bushing and terminal no. 1 as reference. Install CCW stop pin in hole designated ‘X’. Install second stop pin in hole number
corresponding to the number of positions desired. Note that two pole models will begin to repeat when actuated 180º or more.
To retain stop pins, use adhesive mylar washer included; see figure 3.
All models except MX00 models have number of switch positions or stops pre-set at factory and are not adjustable.
Hardware:
Two stop pins, mounting nut, and lockwasher supplied standard.
P/N 537100000
K
36º Indexing Models
30º Indexing Models
Top View
Top View
P/N 537202000
Fig. 1
Fig. 2
Fig. 3
Setting Stops With Stop Rings
ME00, MF00, MG00 & MH00 Models Only:
The number of switch positions or stops are adjustable by means of stop rings provided with each switch. These models are
normally shipped with stop rings and hardware in bulk, not installed. Without stop rings, switches have full 360º rotation and no
stops. Note that all two pole models begin to repeat when actuated 180º or more.
To set stops refer to figures 4 & 5. Orient switch so that terminal no. 1 is as shown. Turn actuator to pos. 1 using flats on bushing
and terminal no. 1 as reference. See figure 6 and install inner stop ring with short tab in hole designated ‘X’. Install outer
stop ring with long tab in hole number corresponding to the number of positions desired. Note that all two pole models begin to
repeat when actuated 180º or more. Use mounting nut and lockwasher to retain stop rings.
All MEXX, MFXX, MGXX & MHXX Models (Except MX00 models):
Number of switch positions or stops are preset at factory, but are user adjustable.
Hardware:
Two stop rings, mounting nut and lockwasher supplied standard.
36º Indexing Models
30º Indexing Models
Top View
Top View
Fig. 4
Fig. 5
Fig. 6
Dimensions are shown: mm
Specifications and dimensions subject to change
www.ck-components.com
K–17