A11215RNZQ C&K Components, A11215RNZQ Datasheet - Page 5
![SWITCH ROTARY SP 12POS EYELET](/photos/15/15/151595/a11215rnzq_sml.jpg)
A11215RNZQ
Manufacturer Part Number
A11215RNZQ
Description
SWITCH ROTARY SP 12POS EYELET
Manufacturer
C&K Components
Series
Ar
Type
Rotary Switchr
Datasheet
1.767B00201.pdf
(5 pages)
Specifications of A11215RNZQ
Number Of Positions
12
Number Of Decks
1
Number Of Poles Per Deck
1
Circuit Per Deck
SP12T
Contact Rating @ Voltage
2.5A @ 125VAC
Actuator Type
Flatted (6.35mm dia)
Mounting Type
Panel Mount
Termination Style
Solder Lug
Orientation
Vertical
Angle Of Throw
30°
No. Of Poles
1
No. Of Switch Positions
12
Contact Current Ac Max
2.5A
Contact Current Dc Max
350mA
Contact Voltage Ac Max
125V
Contact Voltage Dc Max
125V
Circuitry
SP12T
Total # Of Positions
12
Pole Throw Configuration
SP
Actuator Style
Shaft
Actuator Material
Glass/Nylon 6/6
Current Rating (max)
2.5A
Illumination Type
Not Required
Ac Voltage Rating (max)
125VVAC
Dc Voltage Rating (max)
125VVDC
Contact Material
Coin Silver
Contact Plating
Silver
Product Height (mm)
66.94mm
Product Depth (mm)
26.19mm
Product Length (mm)
26.19mm
Operating Temp Range
-30C to 85C
Mounting Style
Panel
Terminal Type
Solder Lug
Index Angle
30 deg
Contact Style
Non Shorting
Dielectric Strength
1000 Vrms
Voltage Rating
125 Volts
Current Rating
2.5 A
Actuator
(STD.) 1.500" high, flatted
Voltage Rating Ac
125 Volts
Voltage Rating Dc
125 Volts
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
*A11215RNZQ
CKC7002
CKC7002
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Setting Stops on A112 and A125 Models
The number of switch positions is adjustable on A112
and A125 models only by means of a stop ring provided
with each switch. The number of positions is pre-set on
all other models and the stop ring is factory installed.
Soldering, Cleaning and Assembly Instructions for ‘MC’ Termination Option
Soldering
1. Insert switch base only into PC board.
2. Do not bend terminals.
3. Wave soldering recommended at
4. Hand solder at 500F, 10 sec.
Switch Assembly
1. Hold housing/shaft assembly by housing. Remove
2. Do not push on switch shaft. Detent mechanism will
3. While holding switch housing, align locating tab on
4. Push firmly on housing until latches snap in place.
5. Remove clip from shaft and discard. Assembly is
Stop ring
PART NO.
767B00201
Material: Brass
Finish: Nickel plated
NONE
500F solder temperature.
max./terminal.
protective cap by squeezing tabs and discard. (FIG. 1)
come apart.
base with notch on housing and engage 4 housing
latches in slots on base. (FIG. 2)
complete. (FIG. 3)
NO SEAL
E
EPOXY SEAL
FUNCTION
AVAILABLE HARDWARE
F
SPLASHPROOF BUSHING SEAL
K–7
Cleaning
1. Flux clean using vapor degreaser and forced
2. Do not allow switch base to ‘trap’ fluids.
3. Freon TMC, TF or Methylene Chloride give
To set stops: Turn shaft fully counter-clockwise and
insert stop ring tab in desired hole. Install lockwasher
and nut to retain stop ring for both PC and panel
mounting. Switch without stop ring has 12 positions.
rinse or triple bath method.
excellent results.
SPLASHPROOF
BUSHING SEAL
(FIG. 1)
1-4 Pole Rotary Switches
REMOVABLE CLIP
K
EPOXY & SPLASHPROOF BUSHING SEAL
Specifications and dimensions subject to change
(FIG. 2)
www.ck-components.com
LOCATING
Dimensions are shown: mm
STANDOFF
A Series
TAB
(FIG. 3)
K