ATMEGA1284PR212-MU Atmel, ATMEGA1284PR212-MU Datasheet - Page 324

no-image

ATMEGA1284PR212-MU

Manufacturer Part Number
ATMEGA1284PR212-MU
Description
BUNDLE ATMEGA1284P/RF212 QFN
Manufacturer
Atmel
Datasheet

Specifications of ATMEGA1284PR212-MU

Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee, 6LoWPAN, ISM
Data Interface
PCB, Surface Mount
Memory Size
128kB Flash, 4kB EEPROM, 16kB RAM
Antenna Connector
PCB, Surface Mount
Package / Case
44-QFN, 32-QFN
Processor Series
ATMEGA128x
Core
AVR8
Data Bus Width
8 bit
Program Memory Type
Flash
Program Memory Size
128 KB
Data Ram Size
16 KB
Development Tools By Supplier
ATAVRRZ541, ATAVRRAVEN, ATAVRRZUSBSTICK, ATAVRISP2, ATAVRRZ201
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Power - Output
-
Operating Temperature
-
Applications
-
Sensitivity
-
Data Rate - Maximum
-
Current - Transmitting
-
Current - Receiving
-
Lead Free Status / Rohs Status
 Details
T
Notes:
8059D–AVR–11/09
A
Symbol
t
I
ACID
CC
= -40°C to 85°C, V
1. All DC Characteristics contained in this datasheet are based on simulation and characterization of other AVR microcon-
2. "Max" means the highest value where the pin is guaranteed to be read as low
3. "Min" means the lowest value where the pin is guaranteed to be read as high
4. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady state
5. Although each I/O port can source more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady
6. All bits set in the
7. Typical values at 25°C. Maximum values are characterized values and not test limits in production
trollers manufactured in the same process technology. These values are preliminary values representing design targets, and
will be updated after characterization of actual silicon.
conditions (non-transient), the following must be observed:
1.)The sum of all IOL, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2.)The sum of all IOL, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3.)The sum of all IOL, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4.)The sum of all IOL, for ports F0-F7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
state conditions (non-transient), the following must be observed:
1)The sum of all IOH, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2)The sum of all IOH, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3)The sum of all IOH, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4)The sum of all IOH, for ports F0-F7 should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Analog Comparator
Propagation Delay
Power Supply Current
Power-save mode
Power-down mode
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
”PRR0 – Power Reduction Register 0” on page
(7)
(7)
(6)
V
WDT disabled, V
Condition
V
Active 1 MHz, V
Active 4 MHz, V
Active 8 MHz, V
Idle 1 MHz, V
Idle 4 MHz, V
Idle 8 MHz, V
32 kHz TOSC enabled,
V
32 kHz TOSC enabled,
V
WDT enabled, V
CC
CC
CC
CC
= 1.8V
= 3V
= 2.7V
= 4.0V
CC
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V)
CC
= 2V
= 3V
= 5V
= 3V
= 3V
Min.
46.
(1)
Typ.
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
750
500
ATmega1284P
Max.
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
(1)
Units
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
ns
324

Related parts for ATMEGA1284PR212-MU