ATMEGA1284PR212-MU Atmel, ATMEGA1284PR212-MU Datasheet - Page 294

• Manufacturer Part Number: ATMEGA1284PR212-MU
• Description: BUNDLE ATMEGA1284P/RF212 QFN
• Manufacturer: Atmel

Specifications of ATMEGA1284PR212-MU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, ISM
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 44-QFN, 32-QFN
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Development Tools By Supplier: ATAVRRZ541, ATAVRRAVEN, ATAVRRZUSBSTICK, ATAVRISP2, ATAVRRZ201
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Power - Output: -
• Operating Temperature: -
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

25.2.1
25.3
25.4
25.5
Table 25-7.
Table 25-8.
25.6
25.6.1
8059D–AVR–11/09
ATmega1284P
ATmega1284P
Device
Device
Signature Bytes
Calibration Byte
Page Size
Parallel Programming Parameters, Pin Mapping, and Commands
Latching of Fuses
Signal Names
No. of Words in a Page and No. of Pages in the Flash
No. of Words in a Page and No. of Pages in the EEPROM
64K words (128 Kbytes)
EEPROM Size
Flash Size
The fuse values are latched when the device enters programming mode and changes of the
fuse values will have no effect until the part leaves Programming mode. This does not apply to
the EESAVE Fuse which will take effect once it is programmed. The fuses are also latched on
Power-up in Normal mode.
All Atmel microcontrollers have a three-byte signature code which identifies the device. This
code can be read in both serial and parallel mode, also when the device is locked. The three
bytes reside in a separate address space. For the ATmega1284P the signature bytes are given
in
Table 25-6.
The ATmega1284P has a byte calibration value for the internal RC Oscillator. This byte resides
in the high byte of address 0x000 in the signature address space. During reset, this byte is auto-
matically written into the OSCCAL Register to ensure correct frequency of the calibrated RC
Oscillator.
This section describes how to parallel program and verify Flash Program memory, EEPROM
Data memory, Memory Lock bits, and Fuse bits in the ATmega1284P. Pulses are assumed to be
at least 250 ns unless otherwise noted.
In this section, some pins of the ATmega1284P are referenced by signal names describing their
functionality during parallel programming, see
295. Pins not described in the following table are referenced by pin names.
4 Kbytes
Part
ATmega1284P
Table
25-6.
Device and JTAG ID
Page Size
128 words
Page Size
0x000
8 bytes
0x1E
Signature Bytes Address
0x001
0x97
PCWORD
PCWORD
EEA[2:0]
PC[6:0]
0x002
0x05
Figure 25-1 on page 295
No. of Pages
No. of Pages
512
512
Part Number
9705
EEA[11:3]
ATmega1284P
PCPAGE
PCPAGE
PC[15:7]
and
JTAG
Figure 25-9 on page
Manufacture ID
0x1F
EEAMSB
PCMSB
11
15
294