ATMEGA1284PR231-AU Atmel, ATMEGA1284PR231-AU Datasheet - Page 30

BUNDLE ATMEGA1284P/RF231 TQFP

ATMEGA1284PR231-AU

Manufacturer Part Number
ATMEGA1284PR231-AU
Description
BUNDLE ATMEGA1284P/RF231 TQFP
Manufacturer
Atmel
Datasheet

Specifications of ATMEGA1284PR231-AU

Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
Data Interface
PCB, Surface Mount
Memory Size
128kB Flash, 4kB EEPROM, 16kB RAM
Antenna Connector
PCB, Surface Mount
Package / Case
44-TQFP, 44-VQFP
Processor Series
ATMEGA128x
Core
AVR8
Data Bus Width
8 bit
Program Memory Type
Flash
Program Memory Size
128 KB
Data Ram Size
16 KB
Development Tools By Supplier
ATAVRRZ541, ATAVRRAVEN, ATAVRRZUSBSTICK, ATAVRISP2, ATAVRRZ201
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Power - Output
-
Operating Temperature
-
Applications
-
Sensitivity
-
Data Rate - Maximum
-
Current - Transmitting
-
Current - Receiving
-
Lead Free Status / Rohs Status
 Details
7.3
8059D–AVR–11/09
Low Power Crystal Oscillator
This Crystal Oscillator is a low power oscillator, with reduced voltage swing on the XTAL2 out-
put. It gives the lowest power consumption, but is not capable of driving other clock inputs, and
may be more susceptible to noise in noisy environments. In these cases, refer to the
Crystal Oscillator” on page
Some initial guidelines for choosing capacitors for use with crystals are given in
crystal should be connected as described in
The Low Power Oscillator can operate in three different modes, each optimized for a specific fre-
quency range. The operating mode is selected by the fuses CKSEL3..1 as shown in
Table 7-3.
Notes:
The CKSEL0 Fuse together with the SUT1..0 Fuses select the start-up times as shown in
7-4.
Table 7-4.
Oscillator Source /
Power Conditions
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Ceramic resonator, BOD
enabled
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Frequency Range
1. The frequency ranges are preliminary values. Actual values are TBD.
2. This option should not be used with crystals, only with ceramic resonators.
3. If 8 MHz frequency exceeds the specification of the device (depends on V
Fuse can be programmed in order to divide the internal frequency by 8. It must be ensured
that the resulting divided clock meets the frequency specification of the device.
8.0 - 16.0
0.4 - 0.9
0.9 - 3.0
3.0 - 8.0
Low Power Crystal Oscillator Operating Modes
Start-up Times for the Low Power Crystal Oscillator Clock Selection
(1)
(MHz)
31.
Start-up Time from
Power-down and
Power-save
258 CK
258 CK
1K CK
1K CK
1K CK
CKSEL3..1
100
101
110
111
”Clock Source Connections” on page
(2)
Additional Delay
14CK + 4.1 ms
14CK + 4.1 ms
Recommended Range for Capacitors C1
14CK + 65 ms
14CK + 65 ms
(V
from Reset
CC
14CK
= 5.0V)
(3)
(2)
(1)
(2)
(1)
(2)
and C2 (pF)
ATmega1284P
12 - 22
12 - 22
12 - 22
CKSEL0
CC
0
0
0
0
1
), the CKDIV8
Table
29.
Table
”Full Swing
SUT1..0
7-3. The
00
01
10
11
00
Table
7-3.
30

Related parts for ATMEGA1284PR231-AU