MICRF010BMTR Micrel Inc, MICRF010BMTR Datasheet
MICRF010BMTR
Specifications of MICRF010BMTR
Related parts for MICRF010BMTR
MICRF010BMTR Summary of contents
Page 1
General Description The MICRF010 is a single chip, ASK/OOK (ON-OFF Keyed) RF receiver IC recommended for new designs replacing the MICRF007. It provides the same function with sensitivity enhancement, typically 6dB better than the MICRF007. Just like all other members ...
Page 2
Micrel Pin Configuration Standard 8-Pin SOIC (M) Pin Description Pin Number Pin Name Pin Function 1 VSS Ground Return (input): ground return to the power supply. See “Applications Information” for bypass capacitor details. 2 ANT Antenna (Input): See “Applications Information” ...
Page 3
Micrel Absolute Maximum Ratings Supply Voltage ( )................................... +7V DDRF DDBB Input/Output Voltage (V ) ................ V I/O Max Input Power ................................................... +20dBm Junction Temperature (T ) ..................................... +150°C J Storage Temperature Range (T )........... –65°C to +150°C ...
Page 4
Micrel Symbol Parameter Digital/Control Section V Input High Voltage IH V Input Low Voltage IL I Output Current OUT V Output High Voltage OH V Output Low Voltage Output Rise and Fall Time R F Notes: ...
Page 5
Micrel Typical Characteristics Supply Current vs. Frequency 6 4.5 3.0 Fix Mode, Continuous Operation 1.5 250 300 350 400 450 500 FREQUENCY (MHz) June 2005 Supply Current vs. Temperature 4.0 ...
Page 6
Micrel Functional Diagram Application Information and Function Description “MICRF010 Block Diagram” above partitioned into three sections: 1) UHF Downconverter, 2) OOK Demodulator, 3) Reference and Control. Also shown in the figure are two external capacitors (C one timing element, which ...
Page 7
Micrel is desired, use crystals with lower ESR, which normally are bigger in size, like the HC49 package. “Application Hints 35” provides additional information and recommended sources for crystals. If using an externally applied signal, it should be AC-coupled and ...
Page 8
Micrel when the devices are used in duty-cycled operation. To further enhance duty-cycled operation, the AGC push and pull currents are boosted for approximately 10ms immediately after the device is taken out of shutdown. This compensates for AGC capacitor voltage ...
Page 9
Micrel The Demodulator Filter Bandwidth There is no external control to set the demodulator bandwidth. The maximum bandwidth is 2000 hertz at 315 MHz. Maximum bandwidth scales linearly with operating frequency. To minimize data pulse stretching, one must calculate the ...
Page 10
Micrel DO Pin The output stage for the digital output (DO) is shown in Figure 4. The output is a 45µA push and 45µA pull switched-current stage. This output stage is capable of driving CMOS loads. An external recommended for ...
Page 11
Micrel Additional Applications Information In addition to the basic operation of the MICRF010, the following enhancements can be made. In particular strongly recommended that the antenna impedance is matched to the input of the IC. Antenna Impedance Matching ...
Page 12
Micrel Application Example: 433.92Mhz, 1000 bps Manchester Encoded On-Off Keyed Receiver 17cm 22 AWG MAGNET WIRE Bill of Materials Item Qty Reference Value 5.6pF 100pF 4.7pF 5 1 C8B NL 6 ...
Page 13
Micrel PCB Layout Information The MICRF010 evaluation board was designed and characterized using two sided 31 mils thick FR4 material with 1 ounce copper clad. If another type of printed circuit board material were to be substituted, impedance matching PCB ...
Page 14
Micrel Package Information 0.026 (0.65) 0.157 (3.99) 0.150 (3.81) 0.064 (1.63) 0.045 (1.14) MICREL, INC. 2180 Fortune DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this ...