HDMIULC6-2M6 STMicroelectronics, HDMIULC6-2M6 Datasheet
HDMIULC6-2M6
Specifications of HDMIULC6-2M6
Available stocks
Related parts for HDMIULC6-2M6
HDMIULC6-2M6 Summary of contents
Page 1
... Higher reliability offered by monolithic integration ■ 500 µm pitch for µQFN 6 leads May 2008 Ultra large bandwidth ESD protection µQFN (pin view) HDMIULC6-2M6 Complies with these standards ■ IEC 61000-4-2 level 4 – air discharge – contact discharge ■ MIL STD883G-Method 3015-7 Applications ■ ...
Page 2
... MIL STD883G-Method 3015 °C) amb Parameter Test Conditions BUS Any I/O pin to GND Any I/O pin to GND = 825 MHz MHz 825 MHz R HDMIULC6-2x6 I/ BUS 4 I/O2 SOT666 Value ±15 ±15 ±25 -55 to +150 125 260 Value Min. Typ. Max 0 8/20 µ 8/20 µ ...
Page 3
... I/O – I/O - 12.00 1000 10000 - 16.00 Figure =5.3GHz 300.0M 1.0G 3.0G Characteristics Line capacitance versus frequency (typical values) HDMIULC6-2M6 V =30mV osc T =25° I-O/GND V BUS C I/O - GND C I I/O F(MHz) 10 100 1000 Frequency response (typical values) HDMIULC6-2M6 S21(db) Fc=5.9GHz F(Hz) 300 ...
Page 4
... Figure 10. Eye diagram at 1.65 Gbps amplitude 500 mV PCB + HDMIULC6-2P6 Horizontal: 100 ps/div Vertical: 200 mV/div 4/17 Figure 9. Eye diagram at 3.2 Gbps amplitude 500 mV PCB + HDMIULC6-2M6 Horizontal: 50 ps/div Vertical: 200 mV/div Figure 11. Eye diagram at 3.2 Gbps amplitude 500 mV PCB + HDMIULC6-2P6 Horizontal: 50 ps/div Vertical: 200 mV/div HDMIULC6-2x6 ...
Page 5
... Tx0- Tx0 Tx0+ Tx0 TMDS TMDS transmitter transmitter HDMI connectors HDMI connectors Tx1- Tx1 video video 2 5 Tx1+ Tx1 audio audio HDMIULC6-2M6 HDMIULC6-2P6 Ctrl / Ctrl / Tx2- Tx2 status status 2 5 Tx2+ Tx2 TC- TC TC+ TC TMDS links TMDS links HDMIULC6-4SC6 HDMIULC6-4SC6 or USBLC6-4SC6 ...
Page 6
... Figure 14. PCB layout example PCB Characteristics Substrate 730 m, Er =3.9 Tracks µm copper Coatinbg µm above substrate µm above tracks 3.4 GND plane on the bottom layer Figure 15. TDR results for HDMIULC6-2M6 with PCB layout example 6/17 Width=100 µm Space=400 µm 3160 Width=215 µm Space=100 µ ...
Page 7
... HDMIULC6-2x6 3 Technical information 3.1 Surge protection The HDMIULC6-2x6 is particularly optimized to perform ESD surge protection based on the rail to rail topology. The clamping voltage with forward drop voltage and TRANSIL Calculation example We assume that the value of the dynamic resistance of the clamping diode is typically ...
Page 8
... GND SURGE SURGE SURGE SURGE TRANSIL TRANSIL F F tr=1ns tr=1ns tr=1ns tr=1ns tr=1ns tr=1ns - NEGATIVE NEGATIVE - - - - - - - - I/O I/O I/O I/O GND GND GND GND SURGE SURGE CL- CL- TEST BOARD TEST BOARD IN IN OUT OUT HDMIULC6-2M6 during negative ESD surge 10V/Div 100ns/Div ...
Page 9
... The perturbed line will be more affected if it works with low voltage signal or high load impedance (few k ). Figure 21. Remaining voltage after the 10V/Div 100ns/Div R G1 Line Line DRIVERS This part of the Technical information HDMIULC6-2P6 during negative ESD surge + RECEIVERS fact the real voltage at this point 2 ...
Page 10
... In usual frequency range of analog signals (up to 240 MHz) the effect on disturbed line is less than -40 dB (see Figure 24 and Figure Figure 24. Analog crosstalk results (typical values) for HDMIULC6-2M6 Figure 25. Analog crosstalk results (typical values) for HDMIULC6-2P6 10/17 TEST BOARD TEST BOARD ...
Page 11
... HDMIULC6-2x6 4 Recommendation on PCB assembly 4.1 Stencil opening design 1. General recommendation on stencil opening design a) Stencil opening dimensions: L (Length), W (Width), T (Thickness) Figure 26. Stencil opening dimensions. b) General Design Rule Stencil thickness ( 125 µm Aspect Ratio Aspect Area 2. Reference design a) Stencil opening thickness: 100 µm b) Stencil opening for leads: Opening to footprint ratio is 90% ...
Page 12
... To control the solder paste amount, the closed via is recommended instead of open vias. 2. The position of tracks and open vias in the solder area should be well balanced. The symmetrical layout is recommended, in case any tilt phenomena caused by asymmetrical solder paste amount due to the solder flow away. 12/17 HDMIULC6-2x6 ...
Page 13
... HDMIULC6-2x6 4.5 Reflow profile Figure 28. ST ECOPACK® recommended soldering reflow profile for PCB mounting Temperature (°C) Temperature (°C) 260°C max 260°C max 255°C 255°C 220°C 220°C 180°C 180°C 125 °C 125 °C ...
Page 14
... 0.50 0.25 [0.020] [0.010] 0.65 [0.026] 0.30 [0.012] HDMIULC6-2x6 Dimensions Millimeters Inches Min. Typ. Max. Min. Typ. 0.50 0.55 0.60 0.020 0.022 0.024 0.00 0.02 0.05 0.000 0.001 0.002 0.18 0.25 0.30 0.007 0.010 0.012 1.45 0.057 1.00 0.039 0.50 0.020 ...
Page 15
... HDMIULC6-2x6 Table 4. SOT-666 dimensions Figure 30. Footprint (dimensions in mm) Ref 0.50 0.99 0.30 Package information Dimensions Millimeters Inches Min. Typ. Max. Min. Typ. 0.45 0.60 0.018 0.08 0.18 0.003 0.17 0.34 0.007 0.19 0.27 0.34 0.007 0.011 0.013 1.50 1.70 0.059 1.50 1 ...
Page 16
... Ordering information 6 Ordering information Table 5. Ordering information Order code HDMIULC6-2M6 HDMIULC6-2P6 1. The marking can be rotated by 90° to diferentiate assembly location 7 Revision history Table 6. Document revision history Date 06-May-2008 16/17 Marking Package Weight (1) T µQFN 6 leads 2 SOT-666 2.9 mg Revision 1 First issue. HDMIULC6-2x6 ...
Page 17
... HDMIULC6-2x6 Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...