MAX792SCPE+ Maxim Integrated Products, MAX792SCPE+ Datasheet - Page 7
![IC SUPERVISOR MPU 16-DIP](/photos/6/57/65728/175-16-dip_sml.jpg)
MAX792SCPE+
Manufacturer Part Number
MAX792SCPE+
Description
IC SUPERVISOR MPU 16-DIP
Manufacturer
Maxim Integrated Products
Type
Simple Reset/Power-On Resetr
Datasheet
1.MAX792SCSE.pdf
(16 pages)
Specifications of MAX792SCPE+
Number Of Voltages Monitored
1
Output
Push-Pull, Push-Pull
Reset
Active High/Active Low
Reset Timeout
140 ms Minimum
Voltage - Threshold
2.91V
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Package / Case
16-DIP (0.300", 7.62mm)
Monitored Voltage
2.75 V to 5.5 V
Undervoltage Threshold
2.85 V
Overvoltage Threshold
3 V
Output Type
Active High, Active Low, Push-Pull
Manual Reset
Resettable
Watchdog
Watchdog
Battery Backup Switching
No Backup
Power-up Reset Delay (typ)
280 ms
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.75 V
Supply Current (typ)
150 uA
Maximum Power Dissipation
842 mW
Maximum Operating Temperature
+ 70 C
Mounting Style
Through Hole
Minimum Operating Temperature
0 C
Power Fail Detection
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
______________________________________________________________Pin Description
PIN
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
LLIN/REF OUT
RESET IN/INT
LOW LINE
CE OUT
NAME
RESET
RESET
WDPO
CE IN
WDO
OVO
GND
SWT
V
WDI
OVI
MR
_______________________________________________________________________________________
CC
Active-Low Reset Output goes low whenever V
old programming mode, or RESET IN falls below 1.30V in external threshold programming mode.
RESET remains low for 200ms typ after the threshold is exceeded on power-up.
Reset is the inverse of RESET.
Input Supply Voltage
Reset-Input/Internal-Mode Select. Connect this input to GND to select internal threshold mode.
Select external programming mode by pulling this input 600mV or higher through an external volt-
age divider.
Low-Line Input/Reference Output connects directly to the low-line comparator in external program-
ming mode (RESET IN/INT ≥ 600mV). Connects directly to the internal 1.30V reference in internal
threshold mode (RESET IN/INT ≤ 60mV).
Overvoltage Comparator Output goes low when OVI is greater than 1.30V. This is an uncommitted
comparator and has no effect on any other internal circuitry.
Inverting Input to the Overvoltage Comparator. When OVI is greater than 1.30V, OVO goes low.
Connect OVI to GND or V
Set Watchdog-Timeout Input. Connect this input to V
timeout period. Connect a capacitor between this input and GND to select another watchdog-
timeout period. Watchdog timeout period = k x (capacitor value in nF)mV, where k = 27 for
V
Manual-Reset Input. This input can be tied to an external momentary pushbutton switch, or to a
logic gate output. Internally pulled up to V
Low-Line Output. LOW LINE goes low 120mV above the reset threshold in internal threshold mode,
or when LLIN/REFOUT goes below 1.30V in external programming mode.
Watchdog Input. If WDI remains either high or low for longer than the watchdog timeout period,
WDPO pulses low and WDO goes low. WDO remains low until the next transition at WDI. Connect to
GND or V
Ground
Chip-Enable Output. CE OUT goes low only when CE IN is low and reset is not asserted. If CE IN is
low when reset is asserted, CE OUT will stay low for 15µs or until CE IN goes high, whichever
occurs first.
Chip-Enable Input—the input to the chip-enable transmission gate. Connect to GND or V
used.
Watchdog Output. WDO goes low if WDI remains either high or low longer than the watchdog time-
out period. WDO returns high on the next transition at WDI.
Watchdog-Pulse Output. Upon the absence of a transition at WDI, WDPO will pulse low for a mini-
mum of 500µs. WDPO precedes WDO by typically 70ns.
CC
= 5V and k = 16.2 for V
CC
Microprocessor and Nonvolatile
if unused.
Memory Supervisory Circuits
CC
CC
when not used.
= 3V. If the watchdog function is unused, connect SWT to V
CC
FUNCTION
.
CC
falls below the reset threshold in internal thresh-
CC
to select the default 1.6sec watchdog
CC
CC
if not
.
7