STM704RM6F STMicroelectronics, STM704RM6F Datasheet - Page 35

• Manufacturer Part Number: STM704RM6F
• Description: SUPERVISOR 3V SWITCH OVER 8SOIC
• Manufacturer: STMicroelectronics
• Type: Simple Reset/Power-On Resetr

Specifications of STM704RM6F

• Number Of Voltages Monitored: 1
• Output: Push-Pull, Totem Pole
• Reset: Active Low
• Reset Timeout: 140 ms Minimum
• Voltage - Threshold: 2.625V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Monitored Voltage: 1 V to 5.5 V
• Output Type: Active Low, Push-Pull
• Manual Reset: Resettable
• Watchdog: No Watchdog
• Battery Backup Switching: Backup
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1 V
• Supply Current (typ): 60 uA
• Maximum Power Dissipation: 320 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Power Fail Detection: Yes
• Undervoltage Threshold: 2.55 V
• Overvoltage Threshold: 2.7 V
• Power-up Reset Delay (typ): 280 ms
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-3831-2

STM690, STM704, STM795, STM802, STM804, STM805, STM806
Table 7.
1. Valid for ambient operating temperature: T
2. V
3. V
4. Tested at V
5. Guaranteed by design.
6. The leakage current measured on the RST pin (STM804/805) or RST pin (STM795) is tested with the reset output not
7. Not valid for STM795/804/805 (open drain).
8. When V
9. When V
10. The reset threshold tolerance is wider for V
Sym
I
noted).
state of RST and RST tested at V
(min). Either V
asserted (output high impedance).
internal oscillation.
SC
CC
CC
supply current, logic input leakage, watchdog functionality, push-button reset functionality, PFI functionality,
(min) = 1.0 V for T
BAT
SW
native
Alter-
BAT
> V
DC and AC characteristics (continued)
> V
CC
CC
= 3.6 V, V
CC
E to E
Reset to E
E
or V
> V
CON
> V
BAT
BAT
SW
A
CON
short circuit current
= 0 °C to +85 °C.
, V
, V
CC
can go to 0 V if the other is greater than 2.0 V.
Description
OUT
OUT
CON
= 3.5 V and 0 V.
propagation delay
remains connected to V
remains connected to V
BAT
high delay
= 3.6 V, and V
A
CC
= –40 to 85 °C; V
rising than for V
Doc ID 10519 Rev 9
CC
= 5.5 V. The state of RST or RST and PFO is tested at V
V
CC
CC
CC
until V
until V
V
Test condition
= 3.6 V, disable mode,
CC
CC
CC
E
= V
falling due to the 10 mV (typ) hysteresis, which prevents
CC
CC
= V
CON
RST
drops below V
drops below the battery voltage (V
RST
= 0 V
(max) to 5.5 V; and V
(max)
(1)
SW
.
Min
0.1
BAT
DC and AC parameters
= 2.8 V (except where
0.75
Typ
10
2
BAT
) - 75 mV.
Max
CC
2.0
7
= V
CC
35/42
Unit
mA
ns
µs