UPD78F1506GF-GAT-AX Renesas Electronics America, UPD78F1506GF-GAT-AX Datasheet - Page 843
UPD78F1506GF-GAT-AX
Manufacturer Part Number
UPD78F1506GF-GAT-AX
Description
MCU 16BIT 78K0R/LX3 128-LQFP
Manufacturer
Renesas Electronics America
Series
78K0R/Lx3r
Datasheet
1.UPD78F1500GK-GAK-AX.pdf
(1016 pages)
Specifications of UPD78F1506GF-GAT-AX
Core Processor
78K/0R
Core Size
16-Bit
Speed
20MHz
Connectivity
3-Wire SIO, I²C, LIN, UART/USART
Peripherals
DMA, LCD, LVD, POR, PWM, WDT
Number Of I /o
78
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 12x12b, D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 843 of 1016
- Download datasheet (7Mb)
78K0R/Lx3
27.4.2 TOOL0 pin
up by connecting it to EV
external resistor, and be sure to keep inputting the V
pin is prohibited).
27.4.3 RESET pin
that is connected to the reset signal generator on the board. To prevent this conflict, isolate the connection with the reset
signal generator.
memory programming mode is set . Do not input any signal other than the reset signal of the dedicated flash memory
programmer.
27.4.4 Port pins
status as that immediately after reset. If external devices connected to the ports do not recognize the port status
immediately after reset, the port pin must be connected to V
27.4.5 REGC pin
27.4.6 X1 and X2 pins
R01UH0004EJ0401 Rev.4.01
Jul 2, 2010
In the flash memory programming mode, connect this pin directly to the dedicated flash memory programmer or pull it
When on-chip debugging is enabled in the normal operation mode, pull this pin up by connecting it to V
Remark The SAU and IICA pins are not used for communication between the 78K0R/Lx3 microcontrollers and
Signal conflict will occur if the reset signal of the dedicated flash memory programmer is connected to the RESET pin
The flash memory will not be correctly programmed if the reset signal is input from the user system while the flash
When the flash memory programming mode is set, all the pins not used for flash memory programming enter the same
Connect the REGC pin to GND via a capacitor (0.47 to 1
Also, use a capacitor with good characteristics, since it is used to stabilize internal voltage.
Connect X1 and X2 in the same status as in the normal operation mode.
Remark In the flash memory programming mode, the internal high-speed oscillation clock (f
dedicated flash memory programmer, because single-line UART is used.
microcontrollers
78K0R/Lx3
Input pin
DD
via an external resistor.
In the flash memory programming mode, a signal output by another device
will conflict with the signal output by the dedicated flash memory
programmer. Therefore, isolate the signal of another device.
Figure 27-5. Signal Conflict (RESET Pin)
Signal conflict
DD
level to the TOOL0 pin before reset is released (pulling down this
DD
μ
F) in the same manner as during normal operation.
Dedicated flash memory programmer
connection pin
or V
Another device
Output pin
SS
via a resistor.
CHAPTER 27 FLASH MEMORY
IH
) is used.
DD
via an
843
Related parts for UPD78F1506GF-GAT-AX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: