R5F61665N50FPV Renesas Electronics America, R5F61665N50FPV Datasheet - Page 1311

• Manufacturer Part Number: R5F61665N50FPV
• Description: MCU FLASH 512K ROM 144-LQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8SX/1600r

Specifications of R5F61665N50FPV

• Core Processor: H8SX
• Core Size: 16/32-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, I²C, IrDA, SCI, SmartCard, USB
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 92
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 144-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

28.8.2
Exit from deep software standby mode is initiated by signals on the external interrupt pins (NMI
and IRQ0-A to IRQ3-A), internal interrupt signals (32K timer, voltage-monitoring interrupt*, and
USB suspend/resume), voltage-monitoring interrupt reset*, power-on reset*, RES pin, or STBY
pin.
1. Exit from deep software standby mode by external interrupt pins or internal interrupt signals
2. Exit from deep software standby mode by a voltage-monitoring reset*
3. Exit from power-on reset*
Deep software standby mode is canceled when any of the DNMIF, DIRQnF (n = 3 to 0),
DT32KIF, DLVDIF*, and DUSBIF bits in DPSIFR is set to 1. The DNMIF or DIRQnF (n = 3
to 0) bit is set to 1 when a specified edge is generated in the NMI or IRQ0-A to IRQ3-A pins,
that has been enabled by the DIRQnE (n = 3 to 0) bit in DPSIER. The rising or falling edge of
the signals can be specified with DPSIEGR. The DT32KIF bit is set to 1 when a 32K timer
interrupt occurs. The DLVDIF bit is set to 1when a voltage-monitoring interrupt occurs. The
DUSBIF bit is set to 1 when a USB suspend/resume interrupt occurs.
When deep software standby mode clearing source is generated, internal power supply starts
simultaneously with the start of clock oscillation, and internal reset signal is generated for the
entire LSI. Once the time specified by the WTSTS5 to WTSTS0 bits in DPSWCR has elapsed,
a stable clock signal is being supplied throughout the LSI and the internal reset is cleared.
Deep software standby mode is canceled on clearing of the internal reset, and then the reset
exception handling starts.
When deep software standby mode is canceled by an external interrupt pin or internal interrupt
signal, the DPSRSTF bit in RSTSR is set to 1.
When a voltage monitoring reset is generated by the power-supply voltage falling, the LSI is
released from deep software standby mode and internal power supply starts simultaneously
with the start of clock oscillation. At the same time, a clock signal is supplied throughout the
LSI. When the power-supply voltage has risen sufficiently, the LSI is released from the
voltage-detection reset state after the clock oscillation stabilization time has been secured. The
CPU then starts reset-exception handling.
When a power-on reset is generated by the power-supply voltage falling, the LSI is released
from deep software standby mode. If the power-supply voltage then rises sufficiently, clock
oscillation starts and the LSI is released from the power-on reset state after the clock
oscillation stabilization time has been secured. As soon as the clock oscillation starts, the clock
signal is provided to the LSI. After that, the CPU starts reset-exception handling.
Exit from Deep Software Standby Mode
Rev. 2.00 Oct. 21, 2009 Page 1277 of 1454
Section 28 Power-Down Modes
REJ09B0498-0200