MC908GT8CBE Freescale Semiconductor, MC908GT8CBE Datasheet - Page 240

• Manufacturer Part Number: MC908GT8CBE
• Description: IC MCU 8K FLASH 8MHZ 42-SDIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GT8CBE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 34
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• Controller Family/series: HC08
• No. Of I/o's: 34
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GT
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Development Support
When the internal address bus matches the value written in the break address registers or when software
writes a 1 to the BRKA bit in the break status and control register, the CPU starts a break interrupt by:
The break interrupt timing is:
By updating a break address and clearing the BRKA bit in a break interrupt routine, a break interrupt can
be generated continuously.
19.2.1.1 Flag Protection During Break Interrupts
The system integration module (SIM) controls whether or not module status bits can be cleared during
the break state. The BCFE bit in the break flag control register (BFCR) enables software to clear status
bits during the break state. See
subsection for each module.
19.2.1.2 TIM1 and TIM2 During Break Interrupts
A break interrupt stops the timer counters.
19.2.1.3 COP During Break Interrupts
The COP is disabled during a break interrupt when V
19.2.2 Break Module Registers
These registers control and monitor operation of the break module:
240
•
•
•
•
•
•
•
•
•
•
Loading the instruction register with the SWI instruction
Loading the program counter with $FFFC and $FFFD ($FEFC and $FEFD in monitor mode)
When a break address is placed at the address of the instruction opcode, the instruction is not
executed until after completion of the break interrupt routine.
When a break address is placed at an address of an instruction operand, the instruction is executed
before the break interrupt.
When software writes a 1 to the BRKA bit, the break interrupt occurs just before the next instruction
is executed.
Break status and control register (BRKSCR)
Break address register high (BRKH)
Break address register low (BRKL)
SIM break status register (SBSR)
SIM break flag control register (SBFCR)
A break address should be placed at the address of the instruction opcode.
When software does not change the break address and clears the BRKA
bit in the first break interrupt routine, the next break interrupt will not be
generated after exiting the interrupt routine even when the internal address
bus matches the value written in the break address registers.
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
15.7.3 SIM Break Flag Control Register
CAUTION
TST
is present on the RST pin.
and the Break Interrupts
Freescale Semiconductor