TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 75

• Manufacturer Part Number: TMP86FS28DFG(JZ)
• Description: IC MCU 8BIT FLASH 60KB 80-LQFP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FS28DFG(JZ)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LCD, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FS28DFGJZ

5.6 Port P5 (P50 to P57)
UART input/output.
register (P5LCR) to “0”.
responding bit in P5LCR and P5OUTCR to “0”.
bit in P5LCR to “0”.
for each bit in P5OUTCR.
state can be read from the P5PRD register.
Port P5 is an 8-bit input/output port that can also be used for timer/counter input/output, LCD segment output, or
A reset initializes the output latch (P5DR) to “1”, the Pch control (P5OUTCR) to “0”, and the LCD output control
To use a pin in Port P5 as an input port, timer/counter input, or UART input, set P5DR to “1” and then set the cor-
To use a pin in Port P5 as an LCD segment output, set the corresponding bit in P5LCR to “1”.
To use a pin in Port P5 as a UART output or timer/counter output, set P5DR to "1" and then set the corresponding
The output circuit of Port P5 can be set either as sink open-drain output (“0”) or CMOS otuput (“1”) individually
Port P5 has a separate data input register. The output latch state can be read from the P5DR register, and the pin
Note: An asterisk (*) indicates that either “1” or “0” can be set.
Output latch read (P5DR)
Data output (P5DR)
Data input (P5PRD)
Table 5-8 Register Programming for Port P5 (P50 to P57)
Port input, UART input, timer/counter input
Port “0” output
Port “1” output, UART output
LCD segment output
P5OUTCRi input
LCD data output
Control output
P5LCRi input
Control input
P5OUTCRi
P5LCRi
OUTEN
STOP
Function
Output latch
D
D
D
Figure 5-7 Port P5
Q
Q
Q
Page 63
P5DR
“1”
“0”
“1”
*
Programmed Value
appropriate.
P5OUTCR
Set as
“0”
*
P5LCR
“0”
“0”
“0”
“1”
P5i
Note) i = 7~0
TMP86FS28DFG