TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 71

• Manufacturer Part Number: TMP86FS28DFG(JZ)
• Description: IC MCU 8BIT FLASH 60KB 80-LQFP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FS28DFG(JZ)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LCD, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FS28DFGJZ

5.4 Port P3 (P30 to P37)
input, serial interface input/output, or UART input/output.
P3DR to “1” and then set the corresponding bit in P3OUTCR to “0”.
for each bit in P3OUTCR.
state can be read from the P3PRD register.
Port P3 is an 8-bit input/output port that can also be used for external interrupt input, divider output, timer/counter
A reset initializes the output latch (P3DR) to “1” and the Pch control (P3OUTCR) to “0”.
To use a pin in Port P3 as an external interrupt input, timer/counter input, serial interface input, or UART input, set
To use a pin in Port P3 as a divider output, serial interface output, or UART output, set P3DR to “1”.
Port 3 can be used for either SIO or UART, so be sure not to enable both of these functions at the same time.
The output circuit of Port P3 can be set either as sink open-drain output (“0”) or CMOS output (“1”) individually
Port P3 has a separate data input register. The output latch state can be read from the P3DR register, and the pin
Output latch read (P3DR)
Data input (P3PRD)
Data output (P3DR)
P3OUTCRi input
Control output
Control input
P3OUTCRi
Table 5-6 Register Programming for Port P3 (P30 to P37)
Port input, external interrupt input, timer/counter
input, serial interface input, UART input
Port “0” output
Port “1” output, serial interface output, UART
output, divider output
OUTEN
STOP
Output latch
D
D
Function
Q
Q
Figure 5-5 Port P3
Page 59
P3DR
“1”
“0”
“1”
Programmed Value
appropriate.
P3OUTCR
Set as
“0”
P3i
Note) i = 7~0
TMP86FS28DFG