TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 68

• Manufacturer Part Number: TMP86FS28DFG(JZ)
• Description: IC MCU 8BIT FLASH 60KB 80-LQFP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FS28DFG(JZ)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LCD, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FS28DFGJZ

5.2 Port P1 (P10 to P17)
Data output (P1DR)
Data output (P1DR)
Note 1: Pins set to input mode read the pin input data. Therefore, when both input and output modes are used in Port P1,
Note 2: For a pin used as an analog input, be sure to clear the corresponding bit in P1CR2 to "0" to prevent flow-through
Note 3: For a pin used as an analog input, do not set P1CR1 to "1" (port output) to prevent the pin from becoming shorted
Note 4: Pins not used as analog inputs can be used as input/output pins. During AD conversion, however, output instruc-
Data input (P1DR)
Data input (P1DR)
Key-on wake-up
P1CR1i input
P1CR2j input
P1CR1j input
P1CR2i input
Analog input
Analog input
the contents of the output latch of a pin set to input mode may be overwritten by a bit manipulation instruction.
current.
with an external signal.
tions must not be executed to ensure the accuracy of conversion results. Also, during AD conversion, do not input
signals that fluctuate widely to pins near analog input pins.
OUTEN
OUTEN
P1CR1i
P1CR2j
P1CR1j
P CR2i
STOPk
AINDS
AINDS
STOP
STOP
SAIN
SAIN
D
D
D
D
D
D
Q
Q
Q
Q
Q
Q
Figure 5-3 Port P1
Page 56
P1i
Note 1) i = 0, 1, 6, 7 : j = 2~5 : k = 2~5
Note 2) STOP = bit 7 in SYSCR1
Note 3) SAIN = AD input select signal
Note 4) STOPk = input select signal for
P1j
key-on wake-up
TMP86FS28DFG