TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 67

• Manufacturer Part Number: TMP86FS28DFG(JZ)
• Description: IC MCU 8BIT FLASH 60KB 80-LQFP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FS28DFG(JZ)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LCD, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FS28DFGJZ

5.2 Port P1 (P10 to P17)
used for analog input or key-on wake-up input.
the function of each pin.
input port.
analog input or key-on wake-up input, set P1CR1 to “0” and then set P1CR2 to “0”.
to “1” and then read P1DR. When P1CR1 = “0” and P1CR2 = “0”, P1DR is read as “0”.
must not be executed to ensure the accuracy of conversion results. Also, during AD conversion, do not input signals
that fluctuate widely to pins near analog input pins.
Port P1 is an 8-bit input/output port that can be configured as an input or an output on a bit basis. Port P1 is also
The Port P1 input/output control register (P1CR1) and Port P1 input control register (P1CR2) are used to specify
A reset initializes P1CR1 to “0”, P1CR2 to “1”, and the output latch (P1DR) to “0” so that Port P1 becomes an
To use a pin in Port P1 as an input port, set P1CR1 to “0” and then set P1CR2 to “1”. To use a pin in Port P1 as an
To use a pin in Port P1 as an output port, set the corresponding bit in P1CR1 to “1”.
To read the output latch data, set P1CR1 to “1”and read P1DR. To read the pin state, set P1CR1 to “0” and P1CR2
Bits not used as analog inputs are used as input/output pins. During AD conversion, however, output instructions
Note: An asterisk (*) indicates that either “1” or “0” can be set.
Table 5-4 Register Programming for Port P1 (P10 to P17)
Port input
Analog input, key-on wake-up input
Port “0” output
Port "1" output
Table 5-5 Values Read from P1DR according to Register Programming
P1CR1
“0”
“0”
“1”
Function
Conditions
P1CR2
“0”
“1”
“0”
“1”
Page 55
P1DR
“0”
“1”
Values Read from P1DR
*
*
Output latch state
Pin state
Programmed Value
“0”
P1CR1
“0”
“0”
“1”
“1”
P1CR2
“1”
“0”
*
*
TMP86FS28DFG