TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 203

• Manufacturer Part Number: TMP86FS28DFG(JZ)
• Description: IC MCU 8BIT FLASH 60KB 80-LQFP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FS28DFG(JZ)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LCD, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FS28DFGJZ

15. Key-on Wakeup (KWU)
15.1 Configuration
15.2 Control
15.3 Function
Key-on Wakeup Control Register
STOPCR
STOP5) pins.
In details, refer to the following section " 15.2 Control ".
enable/disable in 1-bit unit. When those pins are used for STOP mode release, configure corresponding I/O pins to
input mode by I/O port register beforehand.
"L" level on STOP2 to STOP5 pins, which are enabled by STOPCR, for releasing STOP mode (Note1).
(0031H)
In the TMP86FS28DFG, the STOP mode is released by not only P20(
When the STOP mode is released by STOP2 to STOP5 pins, the
STOP2 to STOP5 pins can controlled by Key-on Wakeup Control Register (STOPCR). It can be configured as
Stop mode can be entered by setting up the System Control Register (SYSCR1), and can be exited by detecting the
STOP mode
release signal
(1: Release)
STOP5
STOP5
STOP4
STOP3
STOP2
7
STOP mode released by STOP5
STOP mode released by STOP4
STOP mode released by STOP3
STOP mode released by STOP2
STOP4
6
INT5
STOP3
Figure 15-1 Key-on Wakeup Circuit
5
STOP2
STOPCR
4
(0031H)
3
Page 191
2
0:Disable
1:Enable
0:Disable
1:Enable
0:Disable
1:Enable
0:Disable
1:Enable
1
STOP
pin needs to be used.
INT5
0
/
STOP
(Initial value: 0000 ****)
) pin but also four (STOP2 to
STOP
STOP2
STOP4
STOP3
STOP5
TMP86FS28DFG
Write
Write
Write
Write
only
only
only
only