TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 159

IC MCU 8BIT FLASH 60KB 80-LQFP

TMP86FS28DFG(JZ)

Manufacturer Part Number
TMP86FS28DFG(JZ)
Description
IC MCU 8BIT FLASH 60KB 80-LQFP
Manufacturer
Toshiba
Series
TLCS-870/Cr
Datasheet

Specifications of TMP86FS28DFG(JZ)

Core Processor
870/C
Core Size
8-Bit
Speed
16MHz
Connectivity
SIO, UART/USART
Peripherals
LCD, PWM, WDT
Number Of I /o
62
Program Memory Size
60KB (60K x 8)
Program Memory Type
FLASH
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
80-LQFP
Processor Series
TLCS-870
Core
870/C
Data Bus Width
8 bit
Data Ram Size
2 KB
Interface Type
SIO, UART
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
62
Number Of Timers
6
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Development Tools By Supplier
BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 8 Channel
For Use With
BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
 Details
Other names
TMP86FS28DFGJZ

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TMP86FS28DFG(JZ)
Manufacturer:
Toshiba
Quantity:
10 000
Example :Generating a pulse with 1-ms high-level width and a period of 16.385 ms (fc = 16.0 MHz)
10.3.8 16-Bit Programmable Pulse Generate (PPG) Output Mode (TC5 and 6)
able to enter the 16-bit PPG mode.
the timer register (PWREG5, PWREG6) value is detected, the logic level output from the timer F/F6 is
switched to the opposite state. The counter continues counting. The logic level output from the timer F/F6 is
switched to the opposite state again when a match between the up-counter and the timer register (TTREG5,
TTREG6) value is detected, and the counter is cleared. The INTTC6 interrupt is generated at this time.
generated. Upon reset, the timer F/F6 is cleared to 0.
PWREG5 → PWREG6) (Programming only the upper or lower byte should not be attempted.)
mum frequency to be supplied is fc/2
2 or SLEEP1/2 mode.
This mode is used to generate pulses with up to 16-bits of resolution. The timer counter 5 and 6 are cascad-
The counter counts up using the internal clock or external clock. When a match between the up-counter and
Since the initial value can be set to the timer F/F6 by TC6CR<TFF6>, positive and negative pulses can be
(The logic level output from the
Set the lower byte and upper byte in this order to program the timer register. (TTREG5 → TTREG6,
For PPG output, set the output latch of the I/O port to 1.
Note 1: In the PPG mode, do not change the PWREGi and TTREGi settings while the timer is running. Since
Note 2: When the timer is stopped during PPG output, the
Note 3: i = 5, 6
Two machine cycles are required for the high- or low-level pulse input to the TC5 pin. Therefore, a maxi-
PWREGi and TTREGi are not in the shift register configuration in the PPG mode, the new values pro-
grammed in PWREGi and TTREGi are in effect immediately after programming PWREGi and TTREGi.
Therefore, if PWREGi and TTREGi are changed while the timer is running, an expected operation may not
be obtained.
stopped. To change the output status, program TC6CR<TFF6> after the timer is stopped. Do not change
TC6CR<TFF6> upon stopping of the timer.
Example: Fixing the
CLR (TC6CR).3: Stops the timer
CLR (TC6CR).7: Sets the
LDW
LDW
LD
LD
LD
PPG
Setting ports
(PWREG5), 07D0H
(TTREG5), 8002H
(TC5CR), 33H
(TC6CR), 057H
(TC6CR), 05FH
6 pin to the high level when the TimerCounter is stopped
PPG
PPG
4
6 pin is the opposite to the timer F/F6.)
Hz in the NORMAL1/2 or IDLE1/2 mode, and fs/2
6 pin to the high level
Page 147
: Sets the cycle period.
: Sets the operating clock to fc/2
: Sets TFF6 to the initial value 0, and 16-bit
: Sets the pulse width.
: Starts the timer.
(lower byte).
PPG mode (upper byte).
PPG
6 pin holds the output status when the timer is
3
, and16-bit PPG mode
4
TMP86FS28DFG
to in the SLOW1/

Related parts for TMP86FS28DFG(JZ)