TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 113

• Manufacturer Part Number: TMP86FS28DFG(JZ)
• Description: IC MCU 8BIT FLASH 60KB 80-LQFP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FS28DFG(JZ)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LCD, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FS28DFGJZ

8.2.3.2
Example 1 :Generating an interrupt 1 ms after the rising edge of the input pulse to the TC11 pin
Example 2 :Generating an interrupt when the low-level pulse with 4 ms or more width is input to the TC11 pin
TC11 pin, and counts up at the edge of the internal clock. For the trigger edge used to start counting, either
the rising or falling edge is defined in TC11CR<TC11S>.
width of 12/fc [s] or more is required to ensure edge detection. The rejection circuit is turned off in the
SLOW1/2 or SLEEP1/2 mode, but a pulse width of one machine cycle or more is required.
External Trigger Timer Mode
In the external trigger timer mode, the up-counter starts counting by the input pulse triggering of the
Since the TC11 pin input has the noise rejection, pulses of 4/fc [s] or less are rejected as noise. A pulse
• When TC11CR<METT11> is set to “1” (trigger start and stop)
• When TC11CR<METT11> is set to “0” (trigger start)
(fc =16 MHz)
(fc =16 MHz)
starts, the up-counter is cleared and halted and an INTTC11 interrupt request is generated.
counter and the TC11DRA, the up-counter is cleared and halted without generating an interrupt
request. Therefore, this mode can be used to detect exceeding the specified pulse by interrupt.
starts, the up-counter is cleared and halted and an INTTC11 interrupt request is generated.
counting is ignored if detecting it before detecting a match between the up-counter and the
TC11DRA.
LDW
DI
SET
EI
LD
LD
LDW
DI
SET
EI
LD
LD
When a match between the up-counter and the TC11DRA value is detected after the timer
If the edge opposite to trigger edge is detected before detecting a match between the up-
After being halted, the up-counter restarts counting when the trigger edge is detected.
When a match between the up-counter and the TC11DRA value is detected after the timer
The edge opposite to the trigger edge has no effect in count up. The trigger edge for the next
(TC11DRA), 007DH
(EIRL). 2
(TC11CR), 00000100B
(TC11CR), 00100100B
(TC11DRA), 01F4H
(EIRL). 2
(TC11CR), 00000100B
(TC11CR), 01110100B
Page 101
; 1ms ÷ 2
; IMF= “0”
; Enables INTTC11 interrupt
; IMF= “1”
; Selects the source clock and mode
; Starts TC11 external trigger, METT11 = 0
; 4 ms ÷ 2
; IMF= “0”
; Enables INTTC11 interrupt
; IMF= “1”
; Selects the source clock and mode
; Starts TC11 external trigger, METT11 = 0
7
7
/fc = 7DH
/fc = 1F4H
TMP86FS28DFG