DSPIC30F2020-20E/SP Microchip Technology, DSPIC30F2020-20E/SP Datasheet - Page 9
![IC DSPIC MCU/DSP 12K 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
DSPIC30F2020-20E/SP
Manufacturer Part Number
DSPIC30F2020-20E/SP
Description
IC DSPIC MCU/DSP 12K 28DIP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.AC164335.pdf
(286 pages)
2.DM300023.pdf
(22 pages)
3.DM300023.pdf
(18 pages)
4.DSPIC30F2011-20ISO.pdf
(66 pages)
5.DSPIC30F2011-20IP.pdf
(26 pages)
6.DSPIC30F1010-30ISO.pdf
(26 pages)
7.DSPIC30F1010-30ISO.pdf
(50 pages)
Specifications of DSPIC30F2020-20E/SP
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
21
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-DIP (0.300", 7.62mm)
Core Frequency
15MHz
Core Supply Voltage
5.5V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
21
Flash Memory Size
12KB
Supply Voltage Range
3V To 5.5V
Package
28SPDIP
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
20 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Number Of Programmable I/os
21
Interface Type
I2C/SPI/UART
On-chip Adc
8-chx10-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DM300023 - KIT DEMO DSPICDEM SMPS BUCKDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
19. Module: SPI Module
20. Module: UART Module
21. Module: UART Module
© 2008 Microchip Technology Inc.
Note:
The SMP bit (SPIxCON1<9>, where x = 1 or 2)
does not have any effect when the SPI module is
configured for a 1:1 prescale factor in Master
mode. In this mode, whether the SMP bit is set or
cleared, the data is always sampled at the end of
data output time.
Work around
If sampling at the middle of data output time is
required, then configure the SPI module to use a
clock prescale factor other than 1:1 using the
PPRE<1:0>
SPIxCON1 register.
With the parity option enabled, a parity error,
indicated by the PERR bit (UxSTA<3>) being set,
may occur if the Baud Rate Generator contains an
odd value. This affects both even and odd parity
options.
Work around
Load the Baud Rate Generator register, UxBRG,
with an even value, or disable the peripheral’s
parity option by loading either 0b00 or 0b11 into
the Parity and Data Selection bits, PDSEL<1:0>
(UxMODE<2:1>).
The Receive Buffer Overrun Error Status bit,
OERR (UxSTA<1>), may set before the UART
FIFO has overflowed. After the fourth byte is
received by the UART, the FIFO is full. The OERR
bit should set after the fifth byte has been received
in the UART Shift register. Instead, the OERR bit
may set after the fourth received byte with the
UART Shift register empty.
Work around
After four bytes have been received by the UART,
the UART Receiver Interrupt Flag bit, U1RXIF
(IFS0<11>), will be set, indicating the UART FIFO
is full. The OERR bit may also be set. After reading
the UART receive buffer, UxRXREG, four times to
clear the FIFO, clear both the OERR and UxRXIF
bits in software.
The dsPIC30F1010/202X devices have
only one SPI. All references to x = 2 are
intended for software compatibility with
other dsPIC DSC devices.
and
SPRE<2:0>
bits
in
the
22. Module: UART Module
23. Module: UART Module
24. Module: UART Module
25. Module: UART Module
dsPIC30F1010/202X
UART receptions may be corrupted if the Baud
Rate Generator (BRGH) is set up for 4x mode
(BRGH = 1).
Work around
Use the 16x baud rate option (BRGH = 0) and
adjust the baud rate accordingly.
The UTXISEL0 bit (UxSTA<13>) is always read as
zero regardless of the value written to it. The bit
can be written to either a ‘0’ or ‘1’, but will always
be read as zero. This will affect read-modify-write
operations such as bitwise or shift operations.
Using a read-modify-write instruction on the
UxSTA register (e.g., BSET, BLCR) will always
write the UTXISEL0 bit to zero.
Work around
If a UTXISEL0 value of ‘1’ is needed, avoid using
read-modify-write instructions on the UxSTA
register.
Copy the UxSTA register to a temporary variable
and
read-modify-write operations. Copy the new value
back to the UxSTA register.
The auto-baud feature may not calculate the
correct baud rate when the High Baud Rate
Enable bit, BRGH, is set. With the BRGH set, the
baud rate calculation used is the same as
BRG = 0.
Work around
If the auto-baud feature is needed, use the Low
Baud Rate mode by clearing the BRGH bit.
With the auto-baud feature selected, the Sync
Break character (0x55) may be loaded into the
FIFO as data.
Work around
To prevent the Sync Break character from being
loaded into the FIFO, load the UxBRG register with
either 0x0000 or 0xFFFF prior to enabling the
auto-baud feature (ABAUD = 1).
set
UxSTA<13>
prior
DS80319D-page 9
to
performing