ATMEGA1284P-MUR Atmel, ATMEGA1284P-MUR Datasheet - Page 37

MCU AVR 128KB FLASH 20MHZ 44VQFN

ATMEGA1284P-MUR

Manufacturer Part Number
ATMEGA1284P-MUR
Description
MCU AVR 128KB FLASH 20MHZ 44VQFN
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheets

Specifications of ATMEGA1284P-MUR

Core Processor
AVR
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
128KB (64K x 16)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-VQFN Exposed Pad
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA1284P-MUR
Manufacturer:
FREESCALE
Quantity:
593
8.6
8272A–AVR–01/10
Calibrated Internal RC Oscillator
By default, the Internal RC Oscillator provides an approximate 8 MHz clock. Though voltage and
temperature dependent, this clock can be very accurately calibrated by the the user. See
27-10 on page 334
The device is shipped with the CKDIV8 Fuse programmed. See
page 40
This clock may be selected as the system clock by programming the CKSEL Fuses as shown in
Table
the pre-programmed calibration value into the OSCCAL Register and thereby automatically cal-
ibrates the RC Oscillator. The accuracy of this calibration is shown as Factory calibration in
Table 27-10 on page
By changing the OSCCAL register from SW, see
page
The accuracy of this calibration is shown as User calibration in
When this Oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed cali-
bration value, see the section
Table 8-10.
Notes:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table 8-11 on page
Table 8-11.
Note:
164A/164PA/324A/324PA/644A/644PA/1284/1284P
Power Conditions
BOD enabled
Fast rising power
Slowly rising power
41, it is possible to get a higher calibration accuracy than by using the factory calibration.
8-10. If selected, it will operate with no external components. During reset, hardware loads
1. The device is shipped with this option selected.
2. If 8 MHz frequency exceeds the specification of the device (depends on V
1.
for more details.
The device is shipped with this option selected.
Fuse can be programmed in order to divide the internal frequency by 8.
Internal Calibrated RC Oscillator Operating Modes
Start-up times for the Internal Calibrated RC Oscillator clock selection
Frequency Range
and
37.
334.
”Internal Oscillator Speed” on page 387
7.3 - 8.1
Start-up Time from Power-
”Calibration Byte” on page
down and Power-save
(2)
(MHz)
Reserved
6 CK
6 CK
6 CK
”OSCCAL – Oscillator Calibration Register” on
298.
Additional Delay from
Reset (V
Table 27-10 on page
14CK + 4.1 ms
and
14CK + 65 ms
”System Clock Prescaler” on
14CK
page 439
CC
CKSEL3..0
= 5.0V)
0010
CC
(1)
for more details.
), the CKDIV8
334.
SUT1..0
10
00
01
11
Table
(1)
37

Related parts for ATMEGA1284P-MUR