MC908QY8CDWE Freescale Semiconductor, MC908QY8CDWE Datasheet - Page 46

IC MCU 8BIT 8K FLASH 16-SOIC

MC908QY8CDWE

Manufacturer Part Number
MC908QY8CDWE
Description
IC MCU 8BIT 8K FLASH 16-SOIC
Manufacturer
Freescale Semiconductor
Series
HC08r
Datasheet

Specifications of MC908QY8CDWE

Core Processor
HC08
Core Size
8-Bit
Speed
8MHz
Peripherals
LVD, POR, PWM
Number Of I /o
13
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
16-SOIC (0.300", 7.5mm Width)
Processor Series
HC08QY
Core
HC08
Data Bus Width
8 bit
Data Ram Size
256 B
Maximum Clock Frequency
8 MHz
Number Of Programmable I/os
13
Number Of Timers
2
Operating Supply Voltage
3 V to 5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Development Tools By Supplier
FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
Minimum Operating Temperature
- 40 C
On-chip Adc
4-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Connectivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC908QY8CDWE
Manufacturer:
Winbond
Quantity:
16 700
Part Number:
MC908QY8CDWE
Manufacturer:
FREESCALE
Quantity:
20 000
Analog-to-Digital Converter (ADC10) Module
charging. If externally available, connect the V
ground location.
3.7.5 ADC10 Channel Pins (ADn)
The ADC10 has multiple input channels. Empirical data shows that capacitors on the analog inputs
improve performance in the presence of noise or when the source impedance is high. 0.01 μF capacitors
with good high-frequency characteristics are sufficient. These capacitors are not necessary in all cases,
but when used they must be placed as close as possible to the package pins and be referenced to V
3.8 Registers
These registers control and monitor operation of the ADC10:
3.8.1 ADC10 Status and Control Register
This section describes the function of the ADC10 status and control register (ADSCR). Writing ADSCR
aborts the current conversion and initiates a new conversion (if the ADCH[4:0] bits are equal to a value
other than all 1s).
COCO — Conversion Complete Bit
AIEN — ADC10 Interrupt Enable Bit
ADCO — ADC10 Continuous Conversion Bit
46
COCO is a read-only bit which is set each time a conversion is completed. This bit is cleared whenever
the status and control register is written or whenever the data register (low) is read.
When this bit is set, an interrupt is generated at the end of a conversion. The interrupt signal is cleared
when the data register is read or the status/control register is written.
When this bit is set, the ADC10 will begin to convert samples continuously (continuous conversion
mode) and update the result registers at the end of each conversion, provided the ADCH[4:0] bits do
not decode to all 1s. The ADC10 will continue to convert until the MCU enters reset, the MCU enters
stop mode (if ACLKEN is clear), ADCLK is written, or until ADSCR is written again. If stop is entered
1 = Conversion completed
0 = Conversion not completed
1 = ADC10 interrupt enabled
0 = ADC10 interrupt disabled
ADC10 status and control register, ADSCR
ADC10 data registers, ADRH and ADRL
ADC10 clock register, ADCLK
Reset:
Read:
Write:
Figure 3-3. ADC10 Status and Control Register (ADSCR)
COCO
Bit 7
0
= Unimplemented
AIEN
6
0
MC68HC908QB8 Data Sheet, Rev. 3
ADCO
5
0
REFL
ADCH4
pin to the same potential as V
4
1
ADCH3
3
1
ADCH2
2
1
ADCH1
1
1
SSA
Freescale Semiconductor
ADCH0
at the single point
Bit 0
1
SSA
.

Related parts for MC908QY8CDWE