PIC16C774-I/L Microchip Technology, PIC16C774-I/L Datasheet - Page 138
![IC MCU OTP 4KX14 A/D PWM 44PLCC](/photos/6/63/66325/150-44-plcc_sml.jpg)
PIC16C774-I/L
Manufacturer Part Number
PIC16C774-I/L
Description
IC MCU OTP 4KX14 A/D PWM 44PLCC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16C773SO.pdf
(201 pages)
3.PIC16C774P.pdf
(13 pages)
4.PIC16C774P.pdf
(16 pages)
Specifications of PIC16C774-I/L
Core Size
8-Bit
Program Memory Size
7KB (4K x 14)
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Core Processor
PIC
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Number Of I /o
33
Program Memory Type
OTP
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 10x12b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Controller Family/series
PIC16C
No. Of I/o's
33
Ram Memory Size
256Byte
Cpu Speed
20MHz
No. Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164309 - MODULE SKT FOR PM3 44PLCCISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING444-1001 - DEMO BOARD FOR PICMICRO MCUDVA16XL441 - ADAPTER DEVICE ICE 44PLCC309-1040 - ADAPTER 44-PLCC ZIF TO 40-DIP309-1039 - ADAPTER 44-PLCC TO 40-DIPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
PIC16C774-04I/L
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16C774-I/L
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC16C77X
12.10.1 INT INTERRUPT
External interrupt on RB0/INT pin is edge triggered:
either rising if bit INTEDG (OPTION_REG<6>) is set,
or falling, if the INTEDG bit is clear. When a valid edge
appears
(INTCON<1>) is set. This interrupt can be disabled by
clearing enable bit INTE (INTCON<4>). Flag bit INTF
must be cleared in software in the interrupt service rou-
tine before re-enabling this interrupt. The INT interrupt
can wake-up the processor from SLEEP, if bit INTE was
set prior to going into SLEEP. The status of global inter-
rupt enable bit GIE decides whether or not the proces-
sor branches to the interrupt vector following wake-up.
See
12.10.2 TMR0 INTERRUPT
An overflow (FFh
flag bit T0IF (INTCON<2>). The interrupt can be
enabled/disabled by setting/clearing enable bit T0IE
(INTCON<5>).
EXAMPLE 12-1: SAVING STATUS, W, AND PCLATH REGISTERS IN RAM
DS30275A-page 138
Section 12.13
MOVWF
SWAPF
CLRF
MOVWF
MOVF
MOVWF
CLRF
BCF
MOVF
MOVWF
:
:(ISR)
:
MOVF
MOVWF
SWAPF
MOVWF
SWAPF
SWAPF
on
(Section
the
W_TEMP
STATUS,W
STATUS
STATUS_TEMP
PCLATH, W
PCLATH_TEMP
PCLATH
STATUS, IRP
FSR, W
FSR_TEMP
PCLATH_TEMP, W
PCLATH
STATUS_TEMP,W
STATUS
W_TEMP,F
W_TEMP,W
for details on SLEEP mode.
00h) in the TMR0 register will set
RB0/INT
4.0)
pin,
;Copy W to TEMP register, could be bank one or zero
;Swap status to be saved into W
;bank 0, regardless of current bank, Clears IRP,RP1,RP0
;Save status to bank zero STATUS_TEMP register
;Only required if using pages 1, 2 and/or 3
;Save PCLATH into W
;Page zero, regardless of current page
;Return to Bank 0
;Copy FSR to W
;Copy FSR from W to FSR_TEMP
;Restore PCLATH
;Move W into PCLATH
;Swap STATUS_TEMP register into W
;(sets bank to original state)
;Move W into STATUS register
;Swap W_TEMP
;Swap W_TEMP into W
flag
Advance Information
bit
INTF
12.10.3 PORTB INTCON CHANGE
An input change on PORTB<7:4> sets flag bit RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit RBIE (INTCON<4>).
(Section
12.11
During an interrupt, only the return PC value is saved
on the stack. Typically, users may wish to save key reg-
isters during an interrupt, i.e., W register and STATUS
register. This will have to be implemented in software.
Example 12-1
registers. The register, W_TEMP, must be defined in
each bank and must be defined at the same offset from
the bank base address (i.e., if W_TEMP is defined at
0x20 in bank 0, it must also be defined at 0xA0 in bank
1).
The example:
a)
b)
c)
d)
e)
f)
Stores the W register.
Stores the STATUS register in bank 0.
Stores the PCLATH register.
Executes the interrupt service routine code
(User-generated).
Restores the STATUS register (and bank select
bit).
Restores the W and PCLATH registers.
3.2)
Context Saving During Interrupts
stores and restores the W and STATUS
1999 Microchip Technology Inc.