EZ80F91AZA50SG Zilog, EZ80F91AZA50SG Datasheet - Page 72
EZ80F91AZA50SG
Manufacturer Part Number
EZ80F91AZA50SG
Description
IC ACCLAIM MCU 256KB 144LQFP
Manufacturer
Zilog
Series
eZ80® AcclaimPlus!™r
Datasheet
1.EZ80F91AZA50SG.pdf
(387 pages)
Specifications of EZ80F91AZA50SG
Core Processor
Z8
Core Size
8-Bit
Speed
50MHz
Connectivity
Ethernet, I²C, IrDA, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
144-LQFP
Processor Series
EZ80F91x
Core
eZ80
Data Bus Width
8 bit
Data Ram Size
16 KB
Interface Type
I2C, IrDA, SPI
Maximum Clock Frequency
50 MHz
Number Of Programmable I/os
32
Number Of Timers
4
Operating Supply Voltage
3 V to 3.6 V
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Development Tools By Supplier
eZ80F910300ZCOG
Minimum Operating Temperature
0 C
For Use With
269-4712 - KIT DEV ENCORE 32 SERIES269-4671 - BOARD ZDOTS SBC Z80ACCLAIM PLUS269-4561 - KIT DEV FOR EZ80F91 W/C-COMPILER269-4560 - KIT DEV FOR EZ80F91 W/C-COMPILER
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Details
Other names
269-4564
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 72 of 387
- Download datasheet (5Mb)
eZ80F91 ASSP
Product Specification
64
GPIO Port Interrupts
All interrupts are latched. In effect, an interrupt is held even if the interrupt occurs while
another interrupt is being serviced and interrupts are disabled, or if the interrupt is of a
lower priority. However, before the latched ISR completes its task or re-enables interrupts,
the ISR must clear the interrupt. For on-chip peripherals, the interrupt is cleared when the
data register is accessed. For GPIO-level interrupts, the interrupt signal must be removed
before the ISR completes its task. For GPIO-edge interrupts (single and dual), the interrupt
is cleared by writing a 1 to the corresponding bit position in the Px_ALT0 register. See
Edge Triggered Interrupts
on page 54.
For F91 devices with a ZDI or JTAG revision less than 2, care must be taken using a GPIO
Note:
data register when it is configured for interrupts. For edge-interrupt modes (modes 6 and 9)
as discussed earlier, writing 1 clears the interrupt. However, 1 in the data register also con-
veys a particular configuration. For example, when the data register Px_DR is set first fol-
lowed by the Px_ALT2, Px_ALT1, and Px_DDR registers, then the configuration is
performed correctly. Writing 1 to the register later to clear interrupts does not change the
configuration. For F91 devices with a ZDI or JTAG revision 2 or later, the clearing of inter-
rupts is accomplished through the new Px_ALT0 registers and the above problem does not
exist.
In mode 9 operation, if the GPIO is already configured for mode 9 and if the trigger edge
must be changed (from falling to rising or from rising to falling), then the configuration
must be changed to another mode, such as Mode 2, and then changed back to mode 9. For
example, enter mode 2 by writing the registers in the sequence PxDR, Px_ALT2,
Px_ALT1, Px_DDR. Next, change back to mode 9 by writing the registers in the sequence
PxDR, Px_ALT2, Px_ALT1, Px_DDR.
In Mode 8 operation, if the GPIO is configured for level-sensitive interrupts, a Write value
to Px_DR after configuration must be the same Write value used when configuring the
GPIO.
PS027001-0707
Interrupt Controller
Related parts for EZ80F91AZA50SG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: