PIC24FJ256GA106-I/PT Microchip Technology, PIC24FJ256GA106-I/PT Datasheet - Page 10
![IC PIC MCU FLASH 256K 64TQFP](/photos/6/81/68123/c04-066_pf_sml.jpg)
PIC24FJ256GA106-I/PT
Manufacturer Part Number
PIC24FJ256GA106-I/PT
Description
IC PIC MCU FLASH 256K 64TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Fr
Datasheets
1.PIC24FJ128GA008-IPT.pdf
(12 pages)
2.PIC24FJ128GA106-IPT.pdf
(14 pages)
3.PIC24FJ128GA106-IPT.pdf
(330 pages)
4.PIC24FJ128GA106-IPT.pdf
(52 pages)
5.PIC24FJ256GA106-IPT.pdf
(59 pages)
6.PIC24FJ128GB110-IPF.pdf
(292 pages)
Specifications of PIC24FJ256GA106-I/PT
Program Memory Type
FLASH
Program Memory Size
256KB (85.5K x 24)
Package / Case
64-TFQFP
Core Processor
PIC
Core Size
16-Bit
Speed
32MHz
Connectivity
I²C, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
53
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC24FJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
16 KB
Interface Type
I2C/SPI/UART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
53
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
Minimum Operating Temperature
- 40 C
On-chip Adc
16-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1004 - PIC24 BREAKOUT BOARDMA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC164327 - MODULE SKT FOR 64TQFP
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24FJ256GA106-I/PT
Manufacturer:
AD
Quantity:
201
Company:
Part Number:
PIC24FJ256GA106-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC24FJ256GA110 FAMILY
Data Sheet Clarifications
The following typographic corrections and clarifications
are to be noted for the latest version of the device data
sheet (DS39905D):
1. Module: Guidelines for Getting Started
Section 2.4 Voltage Regulator Pins (ENVREG/
DISVREG and V
with a new and more detailed section. The entire text
follows:
2.4
The on-chip voltage regulator enable/disable pin
(ENVREG or DISVREG, depending on the device
family) must always be connected directly to either a
supply voltage or to ground. The particular connection
is determined by whether or not the regulator is to be
used:
• For ENVREG, tie to V
• For DISVREG, tie to ground to enable the
Refer to Section 25.2 “On-Chip Voltage Regulator”
for details on connecting and using the on-chip
regulator.
TABLE 2-1
DS80368J-page 10
Note:
Note:
or to ground to disable the regulator
regulator or to V
Panasonic
Panasonic
Murata
Murata
Make
TDK
TDK
Voltage Regulator Pins Voltage
Regulator Pins
(ENVREG/DISVREG and
V
CAP
Corrections are shown in bold. Where
possible, the original bold text formatting
has been removed for clarity.
This section applies only to PIC24FJ
devices with an on-chip voltage regulator.
with 16-Bit Microcontrollers
/V
SUITABLE CAPACITOR EQUIVALENTS
DDCORE
CAP
GRM32DR71C106KA01L
GRM31CR61C106KC31L
DD
to disable the regulator
C3216X7R1C106K
C3216X5R1C106K
/V
ECJ-3YX1C106K
ECJ-4YB1C106K
DD
DDCORE
to enable the regulator,
)
Part #
) has been replaced
Capacitance
Nominal
10 µF
10 µF
10 µF
10 µF
10 µF
10 µF
When the regulator is enabled, a low-ESR (< 5Ω)
capacitor is required on the V
stabilize the voltage regulator output voltage. The
V
must use a capacitor of 10 µF connected to ground. The
type can be ceramic or tantalum. Suitable examples of
capacitors are shown in
equivalent specifications can be used.
Designers may use
equivalence of candidate devices.
The placement of this capacitor should be close to
V
length not exceed 0.25 inch (6 mm). Refer to
Section 28.0
additional information.
When the regulator is disabled, the V
must be tied to a voltage supply at the V
Refer to Section 28.0 “Electrical Characteristics” for
information on V
FIGURE 2-3
.
CAP
CAP
Base Tolerance Rated Voltage Temp. Range
0.001
Note:
0.01
/V
/V
0.1
10
1
DDCORE
DDCORE
0.01
±10%
±10%
±10%
±10%
±10%
±10%
Typical data measurement at 25°C, 0V DC bias.
0.1
. It is recommended that the trace
pin must not be connected to V
“Electrical
DD
and V
Frequency (MHz)
FREQUENCY vs. ESR
PERFORMANCE FOR
SUGGESTED V
1
Figure 2-3
2010 Microchip Technology Inc.
DDCORE
Table
16V
16V
16V
16V
16V
16V
10
Characteristics”
CAP
2-1. Capacitors with
.
to evaluate ESR
100
/V
CAP
DDCORE
-55 to 125ºC
-55 to 125ºC
-55 to 125ºC
-55 to 85ºC
-55 to 85ºC
-55 to 85ºC
DDCORE
/V
CAP
1000 10,000
DDCORE
DD
pin to
level.
and
pin
for