ATMEGA328-MU Atmel, ATMEGA328-MU Datasheet - Page 83

• Manufacturer Part Number: ATMEGA328-MU
• Description: IC MCU AVR 32K FLASH 32QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA328-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Processor Series: ATMEGA32x
• Core: AVR
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Operating Temperature Range: - 40 C to + 85 C
• Processor To Be Evaluated: ATMEGA328
• Supply Current (max): 0.2 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13.3.1
8271C–AVR–08/10
Alternate Functions of Port B
The Port B pins with alternate functions are shown in
Table 13-3.
The alternate pin configuration is as follows:
• XTAL2/TOSC2/PCINT7 – Port B, Bit 7
XTAL2: Chip clock Oscillator pin 2. Used as clock pin for crystal Oscillator or Low-frequency
crystal Oscillator. When used as a clock pin, the pin can not be used as an I/O pin.
TOSC2: Timer Oscillator pin 2. Used only if internal calibrated RC Oscillator is selected as chip
clock source, and the asynchronous timer is enabled by the correct setting in ASSR. When the
AS2 bit in ASSR is set (one) and the EXCLK bit is cleared (zero) to enable asynchronous clock-
ing of Timer/Counter2 using the Crystal Oscillator, pin PB7 is disconnected from the port, and
becomes the inverting output of the Oscillator amplifier. In this mode, a crystal Oscillator is con-
nected to this pin, and the pin cannot be used as an I/O pin.
PCINT7: Pin Change Interrupt source 7. The PB7 pin can serve as an external interrupt source.
If PB7 is used as a clock pin, DDB7, PORTB7 and PINB7 will all read 0.
• XTAL1/TOSC1/PCINT6 – Port B, Bit 6
XTAL1: Chip clock Oscillator pin 1. Used for all chip clock sources except internal calibrated RC
Oscillator. When used as a clock pin, the pin can not be used as an I/O pin.
TOSC1: Timer Oscillator pin 1. Used only if internal calibrated RC Oscillator is selected as chip
clock source, and the asynchronous timer is enabled by the correct setting in ASSR. When the
ATmega48A/48PA/88A/88PA/168A/168PA/328/328
Port Pin
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
Port B Pins Alternate Functions
Alternate Functions
XTAL2 (
TOSC2 (
PCINT7 (Pin Change Interrupt 7)
XTAL1 (
TOSC1 (
PCINT6 (Pin Change Interrupt 6)
SCK (SPI Bus Master clock Input)
PCINT5 (Pin Change Interrupt 5)
MISO (SPI Bus Master Input/Slave Output)
PCINT4 (Pin Change Interrupt 4)
MOSI (SPI Bus Master Output/Slave Input)
OC2A (Timer/Counter2 Output Compare Match A Output)
PCINT3 (Pin Change Interrupt 3)
SS (SPI Bus Master Slave select)
OC1B (Timer/Counter1 Output Compare Match B Output)
PCINT2 (Pin Change Interrupt 2)
OC1A (Timer/Counter1 Output Compare Match A Output)
PCINT1 (Pin Change Interrupt 1)
ICP1 (Timer/Counter1 Input Capture Input)
CLKO (Divided System Clock Output)
PCINT0 (Pin Change Interrupt 0)
Chip Clock Oscillator pin 2
Chip Clock Oscillator pin 1 or External clock input
Timer Oscillator pin 2
Timer Oscillator pin 1
)
)
)
Table
13-3.
)
83