NCP45521IMNTWG-H ON Semiconductor, NCP45521IMNTWG-H Datasheet - Page 2

• Manufacturer Part Number: NCP45521IMNTWG-H
• Description: Power Switch ICs - Power Distribution
• Manufacturer: ON Semiconductor

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. NCP45520 only. PG is an open−drain output that requires an external pull up resistor ≥ 1 kW to an external voltage source.
2. Surface−mounted on FR4 board using 1 sq−in pad, 1 oz Cu.
3. Surface−mounted on FR4 board using the minimum recommended pad size, 1 oz Cu.
4. Ensure that the expected operating MOSFET current will not cause the Short−Circuit Protection to turn the MOSFET off undesirably.
5. Tested by the following methods @ T
6. Rating is for all pins except for V
Table 1. PIN DESCRIPTION
Table 2. ABSOLUTE MAXIMUM RATINGS
Supply Voltage Range
Input Voltage Range
Output Voltage Range
EN Digital Input Range
PG Output Voltage Range (Note 1)
Thermal Resistance, Junction−to−Ambient, Steady State (Note 2)
Thermal Resistance, Junction−to−Ambient, Steady State (Note 3)
Thermal Resistance, Junction−to−Case (V
Continuous MOSFET Current @ T
Continuous MOSFET Current @ T
Total Power Dissipation @ T
Derate above T
Total Power Dissipation @ T
Derate above T
Storage Temperature Range
Lead Temperature, Soldering (10 sec.)
ESD Capability, Human Body Model (Notes 5 and 6)
ESD Capability, Machine Model (Note 5)
ESD Capability, Charged Device Model (Note 5)
Latch−up Current Immunity (Notes 5 and 6)
for V
ESD Human Body Model tested per JESD22−A114
ESD Machine Model tested per JESD22−A115
ESD Charged Device Model tested per JESD22−C101
Latch−up Current tested per JESD78
IN
1, 9
7, 8
Pin
2
3
4
5
6
and V
OUT
A
A
= 25°C
= 25°C
should be expected and these devices should be treated as ESD sensitive.
BLEED
Name
V
GND
V
V
EN
PG
SR
OUT
A
A
CC
IN
= 25°C (Note 2)
= 25°C (Note 3)
IN
Rating
A
A
and V
= 25°C (Notes 2 and 4)
= 25°C (Notes 3 and 4)
A
= 25°C:
OUT
Drain of MOSFET (0.5 V – 13.5 V), Pin 1 must be connected to Pin 9
NCP45520−H & NCP45521−H − Active−high digital input used to turn on the MOSFET, pin
has an internal pull down resistor to GND
NCP45520−L & NCP45521−L − Active−low digital input used to turn on the MOSFET, pin has
an internal pull up resistor to V
Supply voltage to controller (3.0 V − 5.5 V)
Controller ground
Load bleed connection, must be tied to V
NCP45520 − Active−high, open−drain output that indicates when the gate of the MOSFET is
fully charged, external pull up resistor ≥ 1 kW to an external voltage source required; tie to
GND if not used
NCP45521 − Slew rate adjustment; float if not used
Source of MOSFET connected to load
IN
Paddle)
which are tied to the internal MOSFET’s Drain and Source. Typical MOSFET ESD performance
http://onsemi.com
2
CC
ESD
ESD
Symbol
ESD
V
T
R
R
R
T
I
I
V
V
V
MAX
MAX
V
P
P
LU
OUT
STG
SLD
θJA
θJA
θJC
CC
EN
PG
IN
D
D
HBM
CDM
MM
OUT
Function
either directly or through a resistor ≤ 1 kW
−0.3 to (V
−40 to 150
−0.3 to 18
−0.3 to 18
−0.3 to 6
−0.3 to 6
Value
40.0
72.7
10.5
2.50
24.9
1.37
13.8
260
200
100
5.3
7.8
3.0
1.0
CC
+ 0.3)
mW/°C
mW/°C
°C/W
°C/W
°C/W
Unit
mA
°C
°C
kV
kV
W
W
V
V
V
V
V
A
A
V