AT49BV320 ATMEL [ATMEL Corporation], AT49BV320 Datasheet
AT49BV320
Available stocks
Related parts for AT49BV320
AT49BV320 Summary of contents
Page 1
... A-1 (LSB Address Input, Byte Mode) BYTE Selects Byte or Word Mode NC No Connect VCCQ Output Power Supply 32-megabit (2M x 16/ 3-volt Only Flash Memory AT49BV320 AT49BV320T AT49BV321 AT49BV321T AT49LV320 AT49LV320T AT49LV321 AT49LV321T Recommend Using AT49BV320A(T)/322A(T) for New Designs. Rev. 1494H–FLASH–01/03 1 ...
Page 2
... I/ GND AT49BV/LV320(T)/321(T) 2 µBGA Top View (Ball Down A13 B A14 C AT49BV/LV320(T) AT49BV320(T) A15 D A16 E VCCQ F GND CBGA Top View (Ball Down AT49BV/LV321( A11 A8 VPP A19 ...
Page 3
... This feature will put the erase or program on hold for any amount of time and let the user read data from or program data to any of the remaining sectors within the memory. The end of a program or an erase cycle is detected by the READY/BUSY pin, Data Polling or by the toggle bit ...
Page 4
... OUTPUT BUFFER INPUT A0 - A20 BUFFER ADDRESS LATCH Y-DECODER X-DECODER AT49BV/LV320(T)/321(T) 4 I/O0 - I/O15/A-1 INPUT BUFFER IDENTIFIER REGISTER STATUS REGISTER COMMAND REGISTER DATA COMPARATOR WRITE STATE MACHINE Y-GATING MAIN MEMORY RESET BYTE RDY/BUSY PROGRAM/ERASE VPP VOLTAGE SWITCH VCC GND 1494H–FLASH–01/03 ...
Page 5
... ERASURE: Before a byte/word can be reprogrammed, it must be erased. The erased state of memory bits is a logical “1”. The entire device can be erased by using the Chip Erase com- mand or individual sectors can be erased by using the Sector Erase command. ...
Page 6
... TOGGLE BIT: In addition to Data Polling the AT49BV/LV32X(T) provides another method for determining the end of a program or erase cycle. During a program or erase operation, suc- cessive attempts to read data from the memory will result in I/O6 toggling between one and zero. Once the program cycle has completed, I/O6 will stop toggling and valid data will be read. Examining the toggle bit may begin at any time during a program cycle. Please see “ ...
Page 7
... The device also supports an erase suspend during a complete chip erase. While the chip erase is suspended, the user can read from any sector within the memory that is pro- tected. The command sequence for a chip erase suspend and a sector erase suspend are the same ...
Page 8
PRODUCT IDENTIFICATION: The product identification mode identifies the device and man- ufacturer as Atmel. It may be accessed by hardware or software operation. The hardware operation mode can be used by an external programmer to identify the correct programming algorithm ...
Page 9
Figure 1. Data Polling Algorithm (Configuration Register = 00) START Read I/O7 - I/O0 Addr = VA YES I/O7 = Data I/O3, I/ YES Read I/O7 - I/O0 Addr = VA YES I/O7 = Data? NO ...
Page 10
Figure 3. Toggle Bit Algorithm (Configuration Register = 00) START Read I/O7 - I/O0 Read I/O7 - I/O0 NO Toggle Bit = Toggle? YES NO I/O3, I/ YES Read I/O7 - I/O0 Twice Toggle Bit = NO Toggle? ...
Page 11
Status Bit Table I/O7 Configuration Register 00 Programming I/O7 Erasing 0 Erase Suspended & Read 1 Erasing Sector Erase Suspended & Read DATA Non-erasing Sector Erase Suspended & I/O7 Program Non-erasing Sector Notes: 1. I/O5 switches to a “1” when ...
Page 12
Command Definition in Hex 1st Bus Cycle Command Bus Sequence Cycles Addr Read 1 Addr Chip Erase 6 555 Sector Erase 6 555 Byte/Word Program 4 555 Enter Single Pulse 6 555 Program Mode Single Pulse 1 Addr Byte/Word Program ...
Page 13
Protection Register Addressing Table Word Use Block 0 Factory 1 Factory 2 Factory 3 Factory 4 User 5 User 6 User 7 User Note: All address lines not specified in the above table must be “0” when accessing the protection ...
Page 14
AT49BV/LV 320/321 – Sector Address Table Sector Size (Bytes/Words) SA0 8K/4K SA1 8K/4K SA2 8K/4K SA3 8K/4K SA4 8K/4K SA5 8K/4K SA6 8K/4K SA7 8K/4K SA8 64K/32K SA9 64K/32K SA10 64K/32K SA11 64K/32K SA12 64K/32K SA13 64K/32K SA14 64K/32K SA15 ...
Page 15
AT49BV/LV 320/321 – Sector Address Table (Continued) Sector Size (Bytes/Words) SA36 64K/32K SA37 64K/32K SA38 64K/32K SA39 64K/32K SA40 64K/32K SA41 64K/32K SA42 64K/32K SA43 64K/32K SA44 64K/32K SA45 64K/32K SA46 64K/32K SA47 64K/32K SA48 64K/32K SA49 64K/32K SA50 64K/32K ...
Page 16
AT49BV/LV 320T/321T – Sector Address Table Sector Size (Bytes/Words) SA0 64K/32K SA1 64K/32K SA2 64K/32K SA3 64K/32K SA4 64K/32K SA5 64K/32K SA6 64K/32K SA7 64K/32K SA8 64K/32K SA9 64K/32K SA10 64K/32K SA11 64K/32K SA12 64K/32K SA13 64K/32K SA14 64K/32K SA15 ...
Page 17
AT49BV/LV 320T/321T – Sector Address Table (Continued) Sector Size (Bytes/Words) SA37 64K/32K SA38 64K/32K SA39 64K/32K SA40 64K/32K SA41 64K/32K SA42 64K/32K SA43 64K/32K SA44 64K/32K SA45 64K/32K SA46 64K/32K SA47 64K/32K SA48 64K/32K SA49 64K/32K SA50 64K/32K SA51 64K/32K ...
Page 18
DC and AC Operating Range Operating Ind. Temperature (Case) V Power Supply CC Operating Modes Mode CE OE Read (2) Program/Erase (1) Standby/Program Inhibit Program Inhibit X ...
Page 19
DC Characteristics Symbol Parameter I Input Load Current LI I Output Leakage Current Standby Current CMOS SB1 Standby Current TTL SB2 Standby Current TTL SB3 CC (1)( Active Read ...
Page 20
AC Read Characteristics Symbol Parameter t Read Cycle Time RC t Address to Output Delay ACC ( Output Delay CE ( Output Delay OE (3)( Output Float DF Output ...
Page 21
Input Test Waveforms and Measurement Level Output Test Load Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: This parameter is characterized and is not 100% tested. 1494H–FLASH–01/ ...
Page 22
AC Byte/Word Load Characteristics Symbol Parameter Address, OE Setup Time AS OES t Address Hold Time AH t Chip Select Setup Time CS t Chip Select Hold Time CH t Write Pulse Width (WE or CE) WP ...
Page 23
Program Cycle Characteristics Symbol Parameter t Byte/Word Programming Time BP t Address Setup Time AS t Address Hold Time AH t Data Setup Time DS t Data Hold Time DH t Write Pulse Width WP t Write Pulse Width High ...
Page 24
Data Polling Characteristics Symbol Parameter t Data Hold Time Hold Time OEH ( Output Delay OE t Write Recovery Time WR Notes: 1. These parameters are characterized and not 100% tested. 2. See t ...
Page 25
Software Product Identification (1) Entry LOAD DATA AA TO ADDRESS 555 LOAD DATA 55 TO ADDRESS AAA LOAD DATA 90 TO ADDRESS 555 ENTER PRODUCT IDENTIFICATION (2)(3)(5) MODE Software Product Identification (1)(6) Exit OR LOAD DATA AA TO ADDRESS 555 ...
Page 26
... AT49BV320(T)/321(T) Ordering Information I (mA ACC (ns) Active Standby 0.01 110 0.01 110 0.01 110 0.01 110 25 0.01 AT49LV320(T)/321(T) Ordering Information I (mA ACC (ns) Active Standby 0.01 48C16 48-ball, Plastic Chip-Size Ball Grid Array Package (CBGA) ...
Page 27
Packaging Information 48C16 – CBGA A1 Ball ID D Top View 2.00 REF Ø Bottom View TITLE 2325 Orchard Parkway San Jose, CA 95131 R 1494H–FLASH–01/ ...
Page 28
TSOP Pin 1 Identifier e E Notes: 1. This package conforms to JEDEC reference MO-142, Variation DD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and on ...
Page 29
Dimensions in Millimeters (Inches) Controlling dimension: millimeters TITLE 2325 Orchard Parkway San Jose, CA 95131 R 1494H–FLASH–01/03 7.70(0.303) 7.50(0.295) 10.50(0.413) 10.30(0.406) 5.25(0.207 0.75(0.0295) ...
Page 30
... Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ® ATMEL is the registered trademark of Atmel. Other terms and product names may be the trademarks of others. Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 Microcontrollers 2325 Orchard Parkway ...