mu9c4480b-90tbi Music Semiconductors, Inc., mu9c4480b-90tbi Datasheet - Page 3

• Manufacturer Part Number: mu9c4480b-90tbi
• Description: Lancam B Family
• Manufacturer: Music Semiconductors, Inc.

Pin Descriptions
PIN DESCRIPTIONS
Note: All signals are implemented in CMOS technology with TTL levels. Signal names that start with a slash (“/”) are active LOW.
Inputs should never be left floating. The CAM architecture draws large currents during compare operations, mandating the use of good
layout and bypassing techniques. Refer to the DC Electrical Characteristics on page 25 for more information.
/E (Chip Enable, Input, TTL)
The /E input enables the device while LOW. The falling
edge registers the control signals /W, /CM, and /EC. The
rising edge locks the daisy chain, turns off the DQ pins,
and clocks the Destination and Source Segment counters.
The four cycle types enabled by /E are shown in Table 1.
Table 1: I/O Cycles
/W (Write Enable, Input, TTL)
The /W input selects the direction of data flow during a
device cycle. /W LOW selects a Write cycle and /W HIGH
selects a Read cycle.
/CM (Data/Command Select, Input, TTL)
The /CM input selects whether the input signals on
DQ15–0 are data or commands. /CM LOW selects
Command cycles and /CM HIGH selects Data cycles.
/EC (Enable Daisy Chain, Input, TTL)
The /EC signal performs two functions. The /EC input
enables the /MF output to show the results of a
comparison, as shown in Figure 9 on page 14. If /EC is
LOW at the falling edge of /E in a given cycle, the /MF
output is enabled. Otherwise, the /MF output is held
HIGH.
Rev. 5.1
TEST2
HIGH
HIGH
LOW
LOW
/W
GND
GND
GND
VCC
VCC
VCC
DQ4
DQ5
DQ6
DQ7
1
2
3
4
5
6
7
8
9
10
11
Figure 2: 44-Pin LQFP
HIGH
HIGH
LOW
LOW
/CM
44-Pin LQFP
(Top View)
Cycle Type
Command Write Cycle
Data Write Cycle
Command Read Cycle
Data Read Cycle
33
32
31
30
29
28
27
26
25
24
23
/MA
/MI
/MF
GND
/RESET
VCC
VCC
TEST1
/E
/W
GND
3
The /EC signal also enables the /MF–/MI daisy chain,
which serves to select the device with the highest-priority
match in a string of LANCAMs. Table 4 explains the
effect of the /EC signal on a device with or without a
match in both Standard and Enhanced modes. /EC must be
HIGH during initialization.
DQ15–0 (Data Bus, I/O, TTL)
The DQ15–0 lines convey data, commands, and status to
and from the LANCAM. /W and /CM control the direction
and nature of the information that flows to or from the
device. When /E is HIGH, DQ15–0 go to HIGH-Z.
/MF (Match Flag, Output, TTL)
The /MF output goes LOW when one or more valid
matches occur during a compare cycle. /MF becomes valid
after /E goes HIGH on the cycle that enables the daisy
chain (on the first cycle that /EC is registered LOW by the
previous falling edge of /E; see Figure 9 on page 14). In a
daisy chain, valid match(es) in higher priority devices are
passed from the /MI input to /MF. If the daisy chain is
enabled but the match flag is disabled in the Control
register, the /MF output only depends on the /MI input of
the device (/MF=/MI). /MF is HIGH if there is no match
or when the daisy chain is disabled (/E goes HIGH when
/EC was HIGH on the previous falling edge of /E). The
System Match flag is the /MF pin of the last device in the
daisy chain. /MF is reset when the active configuration
register set is changed.
TEST2
GND
GND
GND
GND
GND
VCC
VCC
VCC
DQ4
DQ5
DQ6
DQ7
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Figure 3: 64-Pin LQFP
64-Pin LQFP
(Top View)
LANCAM B Family
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
NC
/MA
/MI
/MF
GND
GND
/RESET
VCC
VCC
TEST1
/E
/W
GND
GND
NC
NC