STM32F405RGT6 STMicroelectronics, STM32F405RGT6 Datasheet - Page 83

• Manufacturer Part Number: STM32F405RGT6
• Description: Microcontrollers (MCU) ARM M4 1024 FLASH 168 Mhz 192kB SRAM
• Manufacturer: STMicroelectronics

Specifications of STM32F405RGT6

• Core: ARM Cortex M4
• Processor Series: STM32F4
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 168 MHz
• Program Memory Size: 1024 KB
• Data Ram Size: 192 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 51
• Number Of Timers: 10
• Operating Supply Voltage: 1.7 V to 3.6 V
• Package / Case: LQFP-64
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 16
• Interface Type: CAN, I2C, I2S, SPI, UART
• Program Memory Type: Flash
• Lead Free Status / Rohs Status: Details

STM32F405xx, STM32F407xx
5.3.7
Table 25.
1. Based on characterization, not tested in production.
2. The wakeup times are measured from the wakeup event to the point in which the application code reads the first instruction.
3. t
t
WUSTDBY
WUSTDBY
t
t
WUSLEEP
WUSTOP
Symbol
minimum and maximum values are given at 105 °C and –45 °C, respectively.
(2)(3)
(2)
(2)
Table 24.
1. HSE oscillator with 4 MHz crysta) and PLL are on.
2. I2SMOD bit set in SPI_I2SCFGR register, and then the I2SE bit set to enable I2S peripheral.
3. EN1 bit is set in DAC_CR register.
4. EN2 bit is set in DAC_CR register.
5. ADON bit set in ADC_CR2 register.
Wakeup time from low-power mode
The wakeup times given in
oscillator. The clock source used to wake up the device depends from the current operating
mode:
●
●
All timings are derived from tests performed under ambient temperature and V
voltage conditions summarized in
Low-power mode wakeup timings
APB2
Stop or Standby mode: the clock source is the RC oscillator
Sleep mode: the clock source is the clock that was set before entering Sleep mode.
Wakeup from Sleep mode
Wakeup from Stop mode (regulator in Run mode)
Wakeup from Stop mode (regulator in low power mode)
Wakeup from Stop mode (regulator in low power mode
and Flash memory in Deep power down mode)
Wakeup from Standby mode
Peripheral current consumption (continued)
Peripheral
SDIO
TIM1
TIM8
TIM9
TIM10
TIM11
ADC1
ADC2
ADC3
SPI1
USART1
USART6
(5)
(5)
(5)
(1)
Table 25
Parameter
Doc ID 022152 Rev 2
Table
is measured on a wakeup phase with a 16 MHz HSI RC
11.
168 MHz
0.64
1.47
1.58
0.68
0.45
0.47
2.20
2.04
2.10
0.14
0.34
0.34
Min
260
-
-
-
-
(1)
Electrical characteristics
144 MHz
0.54
1.14
1.22
0.54
0.36
0.38
2.10
1.93
2.00
0.12
0.27
0.28
Typ
110
375
13
17
1
(1)
Max
DD
480
40
-
-
-
(1)
supply
Unit
mA
83/167
Unit
µs
µs
µs