ATA5811-PLQX Atmel, ATA5811-PLQX Datasheet - Page 52
ATA5811-PLQX
Manufacturer Part Number
ATA5811-PLQX
Description
Manufacturer
Atmel
Datasheet
1.ATA5811-PLQX.pdf
(90 pages)
Specifications of ATA5811-PLQX
Operating Temperature (min)
-40C
Operating Temperature (max)
105C
Operating Temperature Classification
Industrial
Product Depth (mm)
7mm
Product Height (mm)
0.9mm
Product Length (mm)
7mm
Lead Free Status / Rohs Status
Compliant
- Current page: 52 of 90
- Download datasheet (2Mb)
Bit-check Mode
Configuration the Bit-check
Figure 42. Timing Diagram for Complete Successful Bit-check (Number of Checked Bits: 3)
52
RX_ACTIVE
ATA5811/ATA5812 [Preliminary]
Demod_Out
Bit check
Start-up mode
T
Startup_Sig_Proc
In Bit-check mode the incoming data stream is examined to distinguish between a valid
signal from a corresponding transmitter and signals due to noise. This is done by subse-
quent time frame checks where the distance between 2 signal edges are continuously
compared to a programmable time window. The maximum count of this edge to edge
test before the transceiver switches to receiving mode is also programmable.
Assuming a modulation scheme that contains 2 edges per bit, two time frame checks
are verifying one bit. This is valid for Manchester, Bi-phase and most other modulation
schemes. The maximum count of bits to be checked can be set to 0, 3, 6 or 9 bits via the
variable N
respectively. If N
receiving mode due to noise. In the presence of a valid transmitter signal, the Bit-check
takes less time if N
is not dependent on N
successful.
According to Figure 43, the time window for the Bit-check is defined by two separate
time limits. If the edge to edge time t
and the upper Bit-check limit T
limit T
switches to sleep mode.
Figure 43. Valid Time Window for Bit-check
1/2 Bit
Lim_min
Demod_Out
Bit-check
or exceeds T
1/2 Bit
Bit-check
in control register 5. This implies 0, 6, 12 and 18 edge to edge checks
Bit-check
Bit-check
is set to a higher value, the transceiver is less likely to switch to
Bit-check mode
1/2 Bit
is set to a lower value. In RX polling mode, the Bit-check time
Lim_max
T
Bit-check
. Figure 42 shows an example where 3 bits are tested
Lim_max
Bit check ok
, the Bit-check will be terminated and the transceiver
1/2 Bit
, the check will be continued. If t
ee
T
T
is in between the lower Bit-check limit T
Lim_min
Lim_max
t
ee
1/2 Bit
1/f
Sig
1/2 Bit
Receiving mode
ee
is smaller than
4689B–RKE–04/04
Lim_min
Related parts for ATA5811-PLQX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
RF Transceiver RF DATA CONTROL Transceiver
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC TXRX UHF ASK/FSK 1CH 48-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Ata5811 Uhf Ask/fsk Transceiver
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
RF Transceiver RF Data Control Transceiver
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: