ISL8483EIB-T Intersil, ISL8483EIB-T Datasheet
ISL8483EIB-T
Specifications of ISL8483EIB-T
Related parts for ISL8483EIB-T
ISL8483EIB-T Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2003, 2004, 2005, 2008. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ISL8483E, ISL8485E FN6048.9 15kV HBM . . . . . . . . . . . . . ± ...
Page 2
... Inputs Open *Shutdown Mode for ISL8483E (see Note 7) 2 ISL8483E, ISL8485E Ordering Information PART NUMBER ISL8483ECPZ (Note) 7 B/Z ISL8483EIB** 6 A/Y ISL8483EIBZ** 5 GND (Note) ISL8483EIP ISL8483EIPZ (Note) ISL8485EABZ** (Note) OUTPUTS ISL8485ECB ISL8485ECBZ (Note ISL8485ECP High-Z High-Z ISL8485ECPZ (Note) High-Z * High-Z * ISL8485EIB** ...
Page 3
Pin Descriptions PIN RO Receiver output > least 0.2V high < 0.2V or more low High if A and B are unconnected (floating). RE Receiver ...
Page 4
... Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C +0.5V) Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below CC http://www.intersil.com/pbfree/Pb-FreeReflow.asp *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in reflow solder processing applications. = 4.5V to 5.5V; Unless Otherwise Specified. ...
Page 5
Electrical Specifications Test Conditions: V Typicals are at V PARAMETER SYMBOL No-Load Supply Current, (Note Shutdown Supply Current I SHDN Driver Short-Circuit Current, I OSD1 V = High or Low O Receiver Short-Circuit Current I OSR SWITCHING ...
Page 6
Electrical Specifications Test Conditions: V Typicals are at V PARAMETER SYMBOL Driver Enable from Shutdown to t ZL(SHDN) Output Low Receiver Enable from Shutdown to t ZH(SHDN) Output High Receiver Enable from Shutdown to t ZL(SHDN) Output Low ESD PERFORMANCE ...
Page 7
Test Circuits and Waveforms SIGNAL GENERATOR FIGURE 2A. TEST CIRCUIT FIGURE 2. DRIVER PROPAGATION DELAY AND DIFFERENTIAL TRANSITION TIMES SIGNAL Y GENERATOR C L (SHDN) FOR ISL8483E ONLY ...
Page 8
Test Circuits and Waveforms SIGNAL A GENERATOR (SHDN) FOR ISL8483E ONLY PARAMETER +1. -1. (Note 6) 0 +1. (Note 6) 0 -1. (Note 9) ...
Page 9
Data Rate, Cables, and Terminations RS485, RS-422 are intended for network lengths up to 4000 feet, but the maximum system data rate decreases as the transmission length increases. Devices operating at 10Mbps are limited to lengths less than 100 feet, ...
Page 10
Typical Performance Curves DIFFERENTIAL OUTPUT VOLTAGE (V) FIGURE 6. DRIVER OUTPUT CURRENT vs DIFFERENTIAL OUTPUT VOLTAGE 160 140 120 LOW 100 80 60 ...
Page 11
Typical Performance Curves PHLY t PHLZ 30 t PLHY 25 20 -40 0 -25 25 TEMPERATURE (°C) FIGURE 12. DRIVER PROPAGATION DELAY vs TEMPERATURE (ISL8485E) R DIFF B A/Y 1 ...
Page 12
Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND TRANSISTOR COUNT: 518 PROCESS: Si Gate CMOS 12 ISL8483E, ISL8485E FN6048.9 September 9, 2008 ...
Page 13
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...
Page 14
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...