AD7490BCPZ Analog Devices Inc, AD7490BCPZ Datasheet - Page 11

• Manufacturer Part Number: AD7490BCPZ
• Description: IC ADC 12BIT 16CH 32-LFCSP
• Manufacturer: Analog Devices Inc

Specifications of AD7490BCPZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 12
• Sampling Rate (per Second): 1M
• Number Of Converters: 1
• Power Dissipation (max): 12.5mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 32-VFQFN, CSP Exposed Pad
• Resolution (bits): 12bit
• Sampling Rate: 1MSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Analog: 2.7V To 5.25V
• Supply Current: 2.5mA
• Digital Ic Case Style: CSP
• Number Of Elements: 1
• Resolution: 12Bit
• Architecture: SAR
• Sample Rate: 1MSPS
• Input Polarity: Unipolar
• Input Type: Voltage
• Rated Input Volt: 2.5/5V
• Differential Input: No
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 3.3/5V
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 12.5mW
• Differential Linearity Error: -0.95LSB/1.5LSB
• Integral Nonlinearity Error: ±1LSB
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: LFCSP EP
• Input Signal Type: Single-Ended
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7490CBZ - BOARD EVAL CONTROL FOR AD7490
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to f
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa
and fb, any active device with nonlinearities creates distortion
products at the sum and difference frequencies of mfa ± nfb,
where m, n = 0, 1, 2, 3, and so on. Intermodulation distortion
terms are those for which neither m nor n are equal to zero.
S
/2 and excluding dc) to the rms value of the
Rev. C | Page 11 of 28
For example, the second order terms include (fa + fb) and
(fa − fb), while the third order terms include (2fa + fb), (2fa − fb),
(fa + 2fb) and (fa − 2fb).
The AD7490 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second order terms are usually distanced in
frequency from the original sine waves, and the third order
terms are usually at a frequency close to the input frequencies.
As a result, the second and third order terms are specified
separately. The calculation of the intermodulation distortion is
per the THD specification, where it is the ratio of the rms sum
of the individual distortion products to the rms amplitude of
the sum of the fundamentals expressed in decibels.
AD7490