MC68HC711E9VFN2 Freescale Semiconductor, MC68HC711E9VFN2 Datasheet - Page 80

no-image

MC68HC711E9VFN2

Manufacturer Part Number
MC68HC711E9VFN2
Description
IC MCU 12K OTP 2MHZ 52-PLCC
Manufacturer
Freescale Semiconductor
Series
HC11r
Datasheets

Specifications of MC68HC711E9VFN2

Core Processor
HC11
Core Size
8-Bit
Speed
2MHz
Connectivity
SCI, SPI
Peripherals
POR, WDT
Number Of I /o
38
Program Memory Size
12KB (12K x 8)
Program Memory Type
OTP
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Package / Case
52-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC68HC711E9VFN2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC68HC711E9VFN2
Quantity:
23
Part Number:
MC68HC711E9VFN2
Quantity:
8
Resets and Interrupts
5.2.2 External Reset (RESET)
The CPU distinguishes between internal and external reset conditions by sensing whether the reset pin
rises to a logic 1 in less than two E-clock cycles after an internal device releases reset. When a reset
condition is sensed, the RESET pin is driven low by an internal device for four E-clock cycles, then
released. Two E-clock cycles later it is sampled. If the pin is still held low, the CPU assumes that an
external reset has occurred. If the pin is high, it indicates that the reset was initiated internally by either
the COP system or the clock monitor.
Do not connect an external resistor capacitor (RC) power-up delay circuit to the reset pin of M68HC11
devices because the circuit charge time constant can cause the device to misinterpret the type of reset
that occurred.
5.2.3 Computer Operating Properly (COP) Reset
The MCU includes a COP system to help protect against software failures. When the COP is enabled, the
software is responsible for keeping a free-running watchdog timer from timing out. When the software is
no longer being executed in the intended sequence, a system reset is initiated.
The state of the NOCOP bit in the CONFIG register determines whether the COP system is enabled or
disabled. To change the enable status of the COP system, change the contents of the CONFIG register
and then perform a system reset. In the special test and bootstrap operating modes, the COP system is
initially inhibited by the disable resets (DISR) control bit in the TEST1 register. The DISR bit can
subsequently be written to 0 to enable COP resets.
The COP timer rate control bits CR[1:0] in the OPTION register determine the COP timeout period. The
system E clock is divided by 2
bits are 0, which selects the fastest timeout period. In normal operating modes, these bits can be written
only once within 64 bus cycles after reset.
80
CR[1:0]
0 0
0 1
1 0
1 1
E/2
Divide
E =
16
64
15
1
4
By
– 0 ms, + 32.8 ms
XTAL = 4.0 MHz
15
131.072 ms
32.768 ms
524.28 ms
Timeout
1.0 MHz
2.098 s
and then further scaled by a factor shown in
Table 5-1. COP Timer Rate Select
M68HC11E Family Data Sheet, Rev. 5.1
– 0 ms, + 16.4 ms
XTAL = 8.0 MHz
CAUTION
16.384 ms
65.536 ms
262.14 ms
Timeout
2.0 MHz
1.049 s
XTAL = 12.0 MHz
– 0 ms, + 10.9 ms
10.923 ms
174.76 ms
43.691 ms
699.05 ms
Timeout
3.0 MHz
Table
XTAL = 16.0 MHz
– 0 ms, + 8.2 ms
Timeout
4.0 MHz
8.19 ms
32.8 ms
5-1. After reset, these
131 ms
524 ms
Freescale Semiconductor

Related parts for MC68HC711E9VFN2