MC68HC711E9VFN2 Freescale Semiconductor, MC68HC711E9VFN2 Datasheet - Page 31

• Manufacturer Part Number: MC68HC711E9VFN2
• Description: IC MCU 12K OTP 2MHZ 52-PLCC
• Manufacturer: Freescale Semiconductor
• Series: HC11r

Specifications of MC68HC711E9VFN2

• Core Processor: HC11
• Core Size: 8-Bit
• Speed: 2MHz
• Connectivity: SCI, SPI
• Peripherals: POR, WDT
• Number Of I /o: 38
• Program Memory Size: 12KB (12K x 8)
• Program Memory Type: OTP
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 52-PLCC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

located in this ROM at $BFC0–$BFFF. The bootstrap ROM contains a small program which initializes the
serial communications interface (SCI) and allows the user to download a program into on-chip RAM. The
size of the downloaded program can be as large as the size of the on-chip RAM. After a 4-character delay,
or after receiving the character for the highest address in RAM, control passes to the loaded program at
$0000. Refer to
Use of an external pullup resistor is required when using the SCI transmitter pin because port D pins are
configured for wired-OR operation by the bootloader. In bootstrap mode, the interrupt vectors are directed
to RAM. This allows the use of interrupts through a jump table. Refer to the application note AN1060
entitled
2.3 Memory Map
The operating mode determines memory mapping and whether external addresses can be accessed.
Refer to
for each of the three families comprising the M68HC11 E series of MCUs.
Memory locations for on-chip resources are the same for both expanded and single-chip modes. Control
bits in the configuration (CONFIG) register allow EPROM and EEPROM (if present) to be disabled from
the memory map. The RAM is mapped to $0000 after reset. It can be placed at any 4-Kbyte boundary
($x000) by writing an appropriate value to the RAM and I/O map register (INIT). The 64-byte register block
is mapped to $1000 after reset and also can be placed at any 4-Kbyte boundary ($x000) by writing an
appropriate value to the INIT register. If RAM and registers are mapped to the same boundary, the first
64 bytes of RAM will be inaccessible.
Refer to
for single-chip mode only.
Freescale Semiconductor
M68HC11 Bootstrap
Figure
Figure
$D000
$FFFF
$B600
$0000
$1000
2-2,
2-7, which details the MCU register and control bit assignments. Reset states shown are
Figure
EXPANDED
Figure
EXT
EXT
2-2,
2-3,
Figure
BOOTSTRAP
Mode, that is included in this data book.
Figure 2-2. Memory Map for MC68HC11E0
Figure
2-3,
M68HC11E Family Data Sheet, Rev. 5.1
2-4,
Figure
SPECIAL
EXT
TEST
EXT
Figure
2-4,
2-5, and
Figure
2-5, and
Figure
FFC0
FFFF
BF00
BFFF
0000
01FF
1000
103F
BOOT
ROM
NORMAL
MODES
INTERRUPT
VECTORS
512 BYTES RAM
64-BYTE REGISTER BLOCK
2-6, which illustrate the memory maps
Figure
2-6.
BFC0
BFFF
SPECIAL MODES
INTERRUPT
VECTORS
Memory Map
31