MC68HC711E9VFN2 Freescale Semiconductor, MC68HC711E9VFN2 Datasheet - Page 197

• Manufacturer Part Number: MC68HC711E9VFN2
• Description: IC MCU 12K OTP 2MHZ 52-PLCC
• Manufacturer: Freescale Semiconductor
• Series: HC11r

Specifications of MC68HC711E9VFN2

• Core Processor: HC11
• Core Size: 8-Bit
• Speed: 2MHz
• Connectivity: SCI, SPI
• Peripherals: POR, WDT
• Number Of I /o: 38
• Program Memory Size: 12KB (12K x 8)
• Program Memory Type: OTP
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 52-PLCC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Figure 2
a 2-MHz E-clock rate) and the alternate baud rate (1200 baud at a 2-MHz E-clock rate). The host
computer sends an initial $FF character, which is used by the bootloader to determine the baud rate that
will be used for the downloading operation. The top half of
Receive data samples at [1] detect the falling edge of the start bit and then verify the start bit by taking a
sample at the center of the start bit time. Samples are then taken at the middle of each bit time [2] to
reconstruct the value of the received character (all 1s in this case). A sample is then taken at the middle
of the stop bit time as a framing check (a 1 is expected) [3]. Unless another character immediately follows
this $FF character, the receive data line will idle in the high state as shown at [4].
The bottom half of
from the host at 1200 baud. Because the receiver is set to 7812 baud, the receive data samples are taken
at the same times as in the upper half of
the start bit at 7812 baud [6].
Freescale Semiconductor
NOTE: Software can change some aspects of the memory map after reset.
$BFC0
$01FF
$BFFF
$FFC0
$0000
$B7FF
$FFFF
$103F
$B600
$BF00
$D000
$1000
shows how the bootloader program differentiates between the default baud rate (7812 baud at
MODA = 0
MODB = 1
SINGLE
CHIP
Figure 2
Figure 1. MC68HC711E9 Composite Memory Map
MULTIPLEXED
EXTERNAL
EXTERNAL
EXTERNAL
EXPANDED
MODA = 1
MODB = 1
shows how the receiver will incorrectly receive the $FF character that is sent
M68HC11 Bootstrap Mode, Rev. 1.1
BOOTSTRAP
MODA = 0
MODB = 0
SPECIAL
Figure
2. The start bit at 1200 baud [5] is 6.5 times as long as
EXTERNAL
EXTERNAL
EXTERNAL
MODA = 1
MODB = 0
SPECIAL
TEST
Figure 2
shows normal reception of $FF.
Automatic Selection of Baud Rate
REGISTER
12K USER
512-BYTE
512-BYTE
EEPROM
64-BYTE
(or OTP)
EPROM
BLOCK
BOOT
ROM
RAM
(MAY BE REMAPPED
TO ANY 4K BOUNDARY)
(MAY BE REMAPPED
TO ANY 4K BOUNDARY)
(MAY BE DISABLED
BY AN EEPROM BIT)
(MAY BE DISABLED
BY AN EEPROM BIT)
VECTORS
VECTORS
SPECIAL
NORMAL
$BFC0
MODE
$FFC0
MODE
$BFFF
$FFFF
197