MPC562MZP56 Freescale Semiconductor, MPC562MZP56 Datasheet - Page 850

• Manufacturer Part Number: MPC562MZP56
• Description: IC MPU 32BIT 56MHZ PPC 388-PBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC562MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 64
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Processor Series: MPC5xx
• Core: PowerPC
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: SCI, SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 22
• Operating Supply Voltage: 2.6 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10 bit, 32 Channel)
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: No

Time Processor Unit 3
19-20
11:13
Bits
9:10
14
15
8
Filter Control
000
001
010
011
100
SOFT RST Soft reset. The TPU3 performs an internal reset when both the SOFT RST bit in the TPUMCR2
ETBANK
FPSCK
Name
DTPU
T2CF
Table 19-20. System Clock Frequency/Minimum Guaranteed Detected Pulse
and the STOP bit in TPUMCR are set. The CPU must write zero to the SOFT RST bit to bring
the TPU3 out of reset. The SOFT RST bit must be asserted for at least nine clocks.
0 Normal operation
1 Puts TPU3 in reset until bit is cleared
NOTE: Do not attempt to access any other TPU3 registers when this bit is asserted. When this
bit is asserted, it is the only accessible bit in the register.
Entry table bank select. This field determines the bank where the microcoded entry table is
situated. After reset, this field is 0b00. This control bit field is write once after reset. ETBANK is
used when the microcode contains entry tables not located in the default bank 0. To execute the
ROM functions on this MCU, ETBANK[1:0] must be 00. Refer to
NOTE: This field should not be modified by the programmer unless necessary because of custom
microcode.
Filter prescaler clock. The filter prescaler clock control bit field determines the ratio between
system clock frequency and minimum detectable pulses. The reset value of these bits is zero,
defining the filter clock as four system clocks. Refer to
T2CLK pin filter control. When asserted, the T2CLK input pin is filtered with the same filter clock
that is supplied to the channels. This control bit is write once after reset.
0 Uses fixed four-clock filter
1 T2CLK input pin filtered with same filter clock that is supplied to the channels
Disable TPU3 pins. When the disable TPU3 control pin is asserted, pin TP15 is configured as an
input disable pin. When the TP15 pin value is zero, all TPU3 output pins are three-stated,
regardless of the pins function. The input is not synchronized. This control bit is write once after
reset.
0 TP15 functions as normal TPU3 channel
1 TP15 pin configured as output disable pin. When TP15 pin is low, all TPU3 output pins are in
a high-impedance state, regardless of the pin function.
Divide By
Table 19-18. TPUMCR2 Bit Descriptions (continued)
16
32
64
4
8
MPC561/MPC563 Reference Manual, Rev. 1.2
Table 19-19. Entry Table Bank Location
ETBANK
20 MHz
200 ns
400 ns
800 ns
1.6 µs
3.2 µs
00
01
10
11
Description
Bank
33 MHz
1.94 µs
121 ns
242 ns
485 ns
970 ns
0
1
2
3
Table
19-20.
40 MHz
1.60 µs
100 ns
200 ns
400 ns
800 ns
Table
19-19.
Freescale Semiconductor
56 MHz
1.14 µs
143 ns
286 ns
571 ns
71 ns