MPC562MZP56 Freescale Semiconductor, MPC562MZP56 Datasheet - Page 664

• Manufacturer Part Number: MPC562MZP56
• Description: IC MPU 32BIT 56MHZ PPC 388-PBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC562MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 64
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Processor Series: MPC5xx
• Core: PowerPC
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: SCI, SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 22
• Operating Supply Voltage: 2.6 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10 bit, 32 Channel)
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: No

Queued Serial Multi-Channel Module
*Reads access the RDRx; writes access the TDRx.
During SCIx initialization, two bits in the SCCxR1 should be written last: the transmitter enable (TE) and
receiver enable (RE) bits, which enable SCIx. Registers SCCxR0 and SCCxR1 should both be initialized
at the same time or before TE and RE are asserted. A single half-word write to SCCxR1 can be used to
initialize SCIx and enable the transmitter and receiver.
15.7.2
SCCxR0 contains the SCIx baud rate selection field and two bits controlling the clock source. The baud
rate must be set before the SCI is enabled. The CPU can read and write SCCxR0 at any time.
Changing the value of SCCxR0 bits during a transfer operation can disrupt the transfer. Before changing
register values, allow the SCI to complete the current transfer, then disable the receiver and transmitter.
15-46
SRESET
Bits
3:15
0
1
2
Field OTHR
Addr
SCI Control Register 0 (SCCxR0)
LNKBD
SCxBR
MSB
OTHR
Name
0
0
—
0x30 504C-6A
0x30 502C —
0x30 504A
LNKBD
This bit is reserved and should always be programmed to 0.
This bit is reserved and should always be programmed to 0.
Reserved
SCI baud rate. The SCI baud rate is programmed by writing a 13-bit value to this field. Writing a
value of zero to SCxBR disables the baud rate generator. Baud clock rate is calculated as follows:
where SCxBR is in the range of 1 to 8191.
Refer to Section 15.7.7.3, “Baud Clock,” for more information.
0
1
Figure 15-26. SCCxR0 — SCI Control Register 0
—
0
2
MPC561/MPC563 Reference Manual, Rev. 1.2
Table 15-24. SCCxR0 Bit Descriptions
QSCI1 Transmit Queue
QSCI1 Receive Queue
3
Table 15-23. SCI Registers
Memory Area
Memory Area
4
5
0x30 5008; 0x30 5020
SCI Baud Rate
6
QSCI1 Transmit Queue Data locations (on
half-word boundary)
QSCI1 Receive Queue Data locations (on
half-word boundary)
Description
7
0_0000_0000_0100
8
=
----------------------------- -
32xSCxBR
SCxBR
f SYS
9
10
11
12
Freescale Semiconductor
13
14
LSB
15