MPC562MZP56 Freescale Semiconductor, MPC562MZP56 Datasheet - Page 1357

IC MPU 32BIT 56MHZ PPC 388-PBGA

MPC562MZP56

Manufacturer Part Number
MPC562MZP56
Description
IC MPU 32BIT 56MHZ PPC 388-PBGA
Manufacturer
Freescale Semiconductor
Series
MPC5xxr
Datasheet

Specifications of MPC562MZP56

Core Processor
PowerPC
Core Size
32-Bit
Speed
56MHz
Connectivity
CAN, EBI/EMI, SCI, SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
64
Program Memory Type
ROMless
Ram Size
32K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 2.7 V
Data Converters
A/D 32x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
388-BGA
Processor Series
MPC5xx
Core
PowerPC
Data Bus Width
32 bit
Data Ram Size
8 KB
Interface Type
SCI, SPI, UART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
56
Number Of Timers
22
Operating Supply Voltage
2.6 V to 5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
2 (10 bit, 32 Channel)
For Use With
MPC564EVB - KIT EVAL FOR MPC561/562/563/564
Lead Free Status / RoHS Status
Request inventory verification / Request inventory verification
Eeprom Size
-
Program Memory Size
-
Lead Free Status / Rohs Status
No

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MPC562MZP56
Manufacturer:
FREESCAL
Quantity:
204
Part Number:
MPC562MZP56
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MPC562MZP56
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MPC562MZP56
Manufacturer:
FREESCALE
Quantity:
7 699
Company:
Part Number:
MPC562MZP56
Quantity:
1 500
Part Number:
MPC562MZP56R2
Manufacturer:
RFT
Quantity:
1 441
Part Number:
MPC562MZP56R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Freescale Semiconductor
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Accuracy tested and guaranteed at V
on page G-7.
This parameter is periodically sampled rather than 100% tested.
Absolute error includes 1/2 count (~2.5 mV) of inherent quantization error and circuit (differential, integral, and offset)
error. Specification assumes that adequate low-pass filtering is present on analog input pins — capacitive filter with
0.01 µF to 0.1 µF capacitor between analog input and analog ground, typical source isolation
impedance of 10 KΩ.
Input signals with large slew rates or high frequency noise components cannot be converted accurately. These signals
may affect the conversion accuracy of other channels.
Below disruptive current conditions, the channel being stressed has conversion values of 0x3FF for analog inputs
greater than V
presence of the sample amplifier. Other channels are not affected by non-disruptive conditions.
Exceeding limit may cause conversion error on stressed channels and on unstressed channels. Transitions within the
limit do not affect device reliability or cause permanent damage.
Input must be current limited to the value specified. To determine the value of the required current-limiting
resistor, calculate resistance values using V
V, then use the larger of the calculated values. The diode drop voltage is a function of current and varies approximately
0.4 to 0.8 V over temperature
This parameter is periodically sampled rather 100% tested.
Derate linearly to 0.3 mA if VDDH - VDDA = 1 V. This specification is preliminary and may change after further
characterization.
Condition applies to two adjacent pins.
Condition applies to all analog channels.
Note that -ve means current flows out of the pin.
Current Coupling Ratio, K, is defined as the ratio of the output current, I
injection current, I
input voltage error on the channel under test is calculated as Verr = I
Maximum source impedance is application-dependent. Error resulting from pin leakage depends on junction
leakage into the pin and on leakage due to charge-sharing with internal capacitance. Error from junction leakage is a
function of external source impedance and input leakage current. In the following expression, expected error in result
value due to junction leakage is expressed in voltage (V
temperature. Charge-sharing leakage is a function of input source impedance, conversion rate, change in voltage
between successive conversions, and the size of the filtering capacitor used. Error levels are best determined
empirically. In general, continuous conversion of the same channel may not be compatible with high source
impedance
For a maximum sampling error of the input voltage <= 1LSB, then the external filter capacitor, C
The value of C
RH
SAMP
and 0x000 for values less than V
INJ
, when both adjacent pins are overstressed with the specified injection current. K = I
in the new design may be reduced.
MPC561/MPC563 Reference Manual, Rev. 1.2
ARH
– V
POSCLAMP
RL
= 1.0V to 0.75 x V
RL
. This assumes that V
= (the lower of V
ERRJ
): V
ERRJ
DDA
= R
INJ
V. See Specification 52 in <XrefBlue>Table G-4
DDA
OUT
* K * R
S
* I
RH
or V
, measured on the pin under test to the
OFF
<= V
S
DDH
where I
.
DDA
) + 0.3 V and V
and V
OFF
66-MHz Electrical Characteristics
is a function of operating
RL
f
>= V
>= 1024 * C
NEGCLAMP
SSA
OUT
due to the
/ I
INJ
= – 0.3
SAMP
The
.
G-51

Related parts for MPC562MZP56