DF70845AD80FPV Renesas Electronics America, DF70845AD80FPV Datasheet - Page 455

• Manufacturer Part Number: DF70845AD80FPV
• Description: IC SUPERH MCU FLASH 112LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7080r

Specifications of DF70845AD80FPV

• Core Size: 32-Bit
• Program Memory Size: 512KB (512K x 8)
• Core Processor: SH-2
• Speed: 80MHz
• Connectivity: EBI/EMI, FIFO, I²C, SCI, SSU
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 76
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V, 4.5V To 5.5V
• Embedded Interface Type: I2C, SCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K570865S001BE - KIT STARTER FOR SH7086R0K570865S000BE - KIT STARTER FOR SH7086HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

10.4
When there is a DMA transfer request, the DMAC starts the transfer according to the
predetermined channel priority; when the transfer end conditions are satisfied, it ends the transfer.
Transfers can be requested in three modes: auto request, external request, and on-chip peripheral
module request. In bus mode, burst mode or cycle steal mode can be selected.
10.4.1
After the DMA source address registers (SAR), DMA destination address registers (DAR), DMA
transfer count registers (DMATCR), DMA channel control registers (CHCR), and DMA operation
register (DMAOR) are set, the DMAC transfers data according to the following procedure:
1. Checks to see if transfer is enabled (DE = 1, DME = 1, TE = 0, AE = 0, NMIF = 0)
2. When a transfer request occurs while transfer is enabled, the DMAC transfers one transfer unit
3. When the specified number of transfer have been completed (when DMATCR reaches 0), the
4. When an address error or an NMI interrupt is generated, the transfer is aborted. Transfers are
Notes: The state of data transfer and registers when transfer by the DMAC is interrupted
Figure 10.2 shows a flowchart of this procedure.
of data (depending on the TS0 and TS1 settings). In auto request mode, the transfer begins
automatically when the DE bit and DME bit are set to 1. The DMATCR value will be
decremented for each transfer. The actual transfer flows vary by address mode and bus mode.
transfer ends normally. If the IE bit in CHCR is set to 1 at this time, a DEI interrupt is sent to
the CPU.
also aborted when the DE bit in CHCR or the DME bit in DMAOR is changed to 0.
1. When DMAC address error has occurred: Data transfer is not performed. However,
2. When an NMI interrupt has occurred: Data transfer is stopped after transferring one
3. When the DE bit in the CHCR and the DME bit in DMAOR are cleared: Data transfer
Operation
DMA Transfer Flow
SAR, DAR, and DMATCR are updated.
transfer unit of data. SAR, DAR, and DMATCR are properly updated.
is stopped after transferring one transfer unit of data. SAR, DAR, and DMATCR are
properly updated.
Section 10 Direct Memory Access Controller (DMAC)
Rev. 3.00 May 17, 2007 Page 397 of 1582
REJ09B0181-0300